1999 Chevrolet Malibu Logo
Anonymous Posted on Sep 03, 2009

My 99 Malibu starts idling rough and dies at anything lower than 500 rpm. I have to brake while pressing the gas pedal in order to keep the car from dying. It has died on me while going downhill at 40 mph, when the rpm's drop; it has died on the freeway, while taking a 25 mph corner on an offramp; it has died while breaking for a red light, etc. The car will start again, but shudders when you give it gas. The car also struggles to start in the morning. You often have to give it gas and keep the rpm's up. Thanks. Jesse

  • 1 more comment 
  • Anonymous Sep 03, 2009

    The engine only shakes when I start it up after dying and quickly step on the gas, as I had to do today when it died on me several times in the middle of the road. It does not feel as though it is misfiring, as it starts up without shaking under normal conditions...I merely have to keep my foot on the gas to keep the engine running. It will shudder right before the engine dies, however.

    The check engine light is not on, though the bulb could very well be burnt out. I hear a "ding, ding, ding" every time I start the vehicle up after it has died, but the only light on my dash is the coolant light, which has been stuck on (another issue all together...I just need to have the code reset).

    This is a 6 cyclinder.

    Thanks.

  • Anonymous Sep 03, 2009

    Is this something that would go out over a long period of time or all at once? This problem has been getting progressively worse for about 6 months now, and has finally resulted in the vehicle dying in response to the problem.

  • Anonymous Sep 03, 2009

    No, the exhaust doesn't smell abnormal or overly-strong in my guesstimation.

×

4 Answers

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Governor:

An expert whose answer got voted for 20 times.

  • Expert 164 Answers
  • Posted on Sep 03, 2009
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Governor:

An expert whose answer got voted for 20 times.

Joined: Aug 24, 2009
Answers
164
Questions
0
Helped
75542
Points
511

Ok does it shake badly, the engine that is? you may have alot going on. is the check engine light on steady or flashing? and 4 cylinder or 6 please

Testimonial: "Awesome! Thank you so much for the quick and insightful help!"

  • Anonymous Sep 03, 2009

    i agree with the bad idle air control solenoid. can also be a vacume leak or a bad mass airflow sensor. tell me this when it restarts hard does the exhaust stink? like rotten eggs? if so im gona say the mass air flow sensor. you can test with a scanner or unplug it temporally, it will run fine but be hesitant when first on the throttle

  • Anonymous Sep 03, 2009

    ok then idle air control it is about 65 bucks and 2 screws to change. good luck with it! also when these fail the check engine light wont illuminate

×

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 8 Answers
  • Posted on Jan 20, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Jan 19, 2010
Answers
8
Questions
1
Helped
7683
Points
16

Mine turned out to be the crank sensor(there are 2 sensors it was the cheaper one that the auto shop says goes bad pretty often in this car)

Ad

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Nov 10, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Nov 10, 2009
Answers
1
Questions
0
Helped
2429
Points
1

It happened to me today on the freakn freeway in bad traffic and construction. im glad my girl didnt go to work today or i would have been on the news. ok here is the solution to the problem: first clean out butterfly valve and intake manifold. next take a look at your spark plugs youre gona have to replace them cause the main culprit is vacuum lines!!! i had 2 bad lines cause it was factory lines. they sucked up too much air into two of my combustion chambers and fouled out my plugs. so check the vacuum lines. cost me 200 bucks to pay a mechanic. but now i know so i can fix it myself. i have a 1999 chevy malibu 4 cylinder hope this helps

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

  • Master 713 Answers
  • Posted on Sep 03, 2009
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Joined: Aug 20, 2009
Answers
713
Questions
0
Helped
296944
Points
2393

It is likely that the idle air control valve or the throttle position sensor is bad on the vehicle this could cause the hard starts and the idle situation at stops.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

Engine running rough all of the sudden

Try Maf sensor,(Mass air flow)
Then try tps sensor, (throttle position sensor)
Unable to answer exactly without looking up codes
0helpful
1answer

2009 mini cooper clubman with sport button-delay when press on gas.

The fuel pressure and fuel system needs to be inspected.
-------
I suggest you few helk links.Click the link below and follow its troubleshooting procedure:------------------Pushing on the gas pedal, but the car slows down? Gas pedal to the floor and the car slows down? http://technoanswers.blogspot.in/2012/02/pushing-on-gas-pedal-but-car-slows-down.html
-------------
Car dies when gas pedal is pressed? http://schematicsdiagram.blogspot.com/2011/12/car-dies-when-gas-pedal-is-pressed.html
---------------
Car won't start without hitting the gas pedal? http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-without-hitting-gas.html
-------------Car only starts when gas pedal is pressed? http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html
----------1999 Ford F-150 Idles rough and quits when gas pedal is pressed less? http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html
----------Delay starting on Toyota Prius? http://schematicsdiagram.blogspot.in/2012/02/delay-starting-on-toyota-prius.html

--------
These will help.
Thanks.
0helpful
1answer

1990 Chevy Van with a 350 small block that has a mind of it's own.

Try to get it running a bit to warm up the exhaust. Take a point and shoot thermometer and take the temp of the cat. If temps exceed 400 degrees I would start to suspect a plugged cat.
0helpful
2answers

I have 1999Chevy suburban with 6.5 turbo diesel motor.it idles up and down and when driving the gas pedal is real touchy Wat is the problem and were do i locate the problem

Check the help links related to this problem.Click the link below to go through its troubleshooting procedure :-----Idles rough and quits when gas pedal is pressed less? http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html---------
Car won't start without hitting the gas pedal? http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-without-hitting-gas.html
-------Complete loss of brake pedal then all gets normal? http://repairhelpcenter.blogspot.com/2012/01/complete-loss-of-brake-pedal-then-all.html
------Car dies when gas pedal is pressed? http://schematicsdiagram.blogspot.com/2011/12/car-dies-when-gas-pedal-is-pressed.html
--------Pushing on the gas pedal, but the car slows down? Gas pedal to the floor and the car slows down?

http://technoanswers.blogspot.in/2012/02/pushing-on-gas-pedal-but-car-slows-down.html

---------

After replacing brake rotors and pads, brake pedal remains on floor? http://technoanswers.blogspot.in/2012/02/after-replacing-brake-rotors-and-pads.html

---------

accelerator pedal sensor? http://technoanswers.blogspot.in/2012/02/2009-chevy-impala-accelerator-pedal.html

-------

For rough idle issues and problem troubleshooting,go through the help links provided below :----- van idles rough?

http://howtobyme.blogspot.in/2012/01/2004-ford-freestar-van-idles-rough.html

---------
will not idle when cold?

http://technoanswers.blogspot.in/2012/02/ford-explorer-40-will-not-idle-when.html

----------
runs lean and idles rough?

http://technoanswers.blogspot.in/2012/02/ford-runs-lean-and-idles-rough.html

-----------
Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------
Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

----------
Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

---------
Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

----------
Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

------------
Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

------
While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

This will help.

Thanks.

0helpful
1answer

Car starts after taking foot off gas car shuts down 2001 mit 3.0 v-6 spider

For this problem, i suggest you to go through this help links.Click the link below to go through the troubleshooting procedure :----Car Idles rough and quits when gas pedal is pressed less? http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html-----------Car only starts when gas pedal is pressed? http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html
-----------Car won't start without hitting the gas pedal? http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-without-hitting-gas.html
---------Car dies when gas pedal is pressed? http://schematicsdiagram.blogspot.com/2011/12/car-dies-when-gas-pedal-is-pressed.html
------------Pushing on the gas pedal, but the car slows down? Gas pedal to the floor and the car slows down? http://technoanswers.blogspot.in/2012/02/pushing-on-gas-pedal-but-car-slows-down.html
-----------This will help.Thanks.
0helpful
1answer

Car shut down when foot not on the accelerator

For this types of problem,there are few help links.I suggest you to click the link below and go through the troubleshooting procedure :-----Car only starts when gas pedal is pressed? http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html-----------Car won't start without hitting the gas pedal? http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-without-hitting-gas.html
----------Complete loss of brake pedal then all gets normal? http://repairhelpcenter.blogspot.com/2012/01/complete-loss-of-brake-pedal-then-all.html
----------Car dies when gas pedal is pressed? http://schematicsdiagram.blogspot.com/2011/12/car-dies-when-gas-pedal-is-pressed.html
--------------Pushing on the gas pedal, but the car slows down? Gas pedal to the floor and the car slows down? http://technoanswers.blogspot.in/2012/02/pushing-on-gas-pedal-but-car-slows-down.html
-------------Idles rough and quits when gas pedal is pressed less? http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html----------This will help.Thanks.
1helpful
1answer

My 99 malibu starts and dies right away. It won't stay on unless I keep the gas pedal down and rpm above 1500

the ( iac ) idle air control is sticking and needs cleaned. heres how to clean. locate it on the throttle body, remove wire connector, remove the torx screws that hold it on. when off of car. clean valve on end you can use a old toothbrush or similar to do this. do not push in on valve it will mess up idle setting. on the 3.1 the setting is 1 and 1/8 from tip of valve to body of iac. you can use gumout spray or throttlebody cleaner. here are a few symtoms-- stalls after starts, when cold or hot. stalling on deceleration, stalls at idle, unstable idle, low idle, or stuck on high idle. hope this helps !
0helpful
1answer

Engine will start and rough idle but dies when either the brakes are applied or the lights are turned on!

have you checked out your fuel filter? I had my 2003 denali do the same type of problem and it turned out to be a very dirty fuel filter.
Not finding what you are looking for?

2,439 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...