Hi there, I have a 2007 XC90 AWD with 336mm vented rotors. What it the minimum brake rotor thickness. Thanks

Each brake rotor has the minimum thickness marked on the rotor. Keep in mind also that the comparative thickness of each side of a vented rotor must be considered. Even if the overall thickness is greater than the minimum, each side must be within .040" (1mm) of the other.

The minimum rotor thickness is normally cast into the rotor. You will find it printed either on the outside hat section of the rotor or on the very top edge section of the rotor.
There are some example pictures here

http://forums.justcommodores.com.au/dba-brakes/249789-dba-tech-talk-when-your-rotors-undersize-rotor-minimum-thickness.html

Most rotors won't make it past one set of pads for thickness. If they are smooth and not warp(pedal or steering wheel shakes when braking), Reuse them. Using this theory you can get up to 3 sets of pads off the rotors. The minimum thickness is stamped on the edge of the rotors.

Hello there
From a kind chap on this page
http://buickforums.com/forums/threads/18395-Service-limits-for-brake-rotors

For a 2000 Buick LeSabre

FRONT BRAKE ROTORS:
Discard Thickness30.7 mm (1.209 in.)
Lateral Runout (New)0.06 mm (0.002 in.)
Minimum Thickness after Refinish31.08 mm (1.224 in.)
Rotor Diameter 15 inch Wheels (New)278.0 mm (10.9 in.)
Rotor Diameter 16 inch Wheels (New)303.0 mm (11.9 in.)
Rotor Thickness (New)32.20 mm (1.267 in.)
Thickness Variation (New)0.025 mm (0.001 in.)

Rear Brakes JC5/JH5 Utility Only
Rotor Discard Thickness* .............................. 28.50 mm (1.122 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 29.0 mm (1.142 inch)
Rotor Thickness-new .................................... 30.0 mm (1.181 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

Rear Brakes JH6
Rotor Discard Thickness * ............................. 27.50 mm (1.082 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 28.0 mm (1.102 inch)
Rotor Thickness-new .................................... 29.0 mm (1.141 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

THE REAR BRAKES ARE 8.4mm(1.024")!!! DO NOT TURN YOUR FRONT ROTORS TO THIS!!! The front are a minimum of 26mm (1.024")

All are different, on the back side of the brake rotor , will have a stamp with (MIN) and some number after it the will be the minimum spec thickness for the brake rotor.

The standard vented rotor is 20mm (0.787 inches) thick and should be ground to no less than 18.5mm (0.728 inches) for your vehicle. The measurement is taken with a micrometer measuring total thickness from inside of rotor to the outside of the rotor.
Good luck.
Regards,

depends on your state/province and common sense. if you must ask this question, replace the rotors.

there is many kind of brake system of ur truck here i will send u everything about the brake and i hope its help

Rear Brakes JC3

Rotor Discard Thickness* 18.50 mm/0.728 in Rotor Minimum Allowable Thickness After Refinish 19.0 mm/0.748 in Rotor Thickness (new) 20.0 mm/0.787 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JC4

Rotor Discard Thickness* 28.50 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring1 .50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH2

Rotor Discard Thickness* 28.50 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH6

Rotor Discard Thickness* 27.50 mm/1.082 in Rotor Minimum Allowable Thickness After Refinish 28.0 mm/1.102 in Rotor Thickness (new) 29.0 mm/1.141 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH7

Rotor Discard Thickness* 28.5 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this Specification. After refinishing the rotor, replace any rotor that does not meet the minimum or discard thickness specifications.