1995 Lexus SC300 drivers side window made a popping noise and now will not stay up. I removed the door panel and if I push the window up manually, I can roll it down but not back up. Anyone know how to fix?

images for Where is crankshaft sensor location on 95 ...

eplaced engine on '97 SC300 now new engine does not have Crank ...

www.clublexus.com/.../633233-replaced-engine-on-97-sc300-now-new-...

May 4, 2012 - Location: arizona. Posts: 3 ... apparently 95-97s had an additional crank sensor. .... 1995 Lexus SC300 5spd Na-T ( TT Ecu Mod + a few others) 2jzge position sensor??
Nov 2, 2011
SC400 Crank Shaft Position Sensor. WHERE?????
Oct 11, 2011
SC300 No Spark
Oct 2, 2010
What happens if the Camshaft Position Sensor goes bad?
Jun 18, 2009
More results from www.clublexus.com

Lexus Crank Position Sensor ' LS400 SC300 ES300 GS300 ...

www.partsgeek.com > Crank Position Sensor > Lexus Parts & Accessories

Products 1 - 10 of 68 - 95 1995 Lexus LS400 Crank Position Sensor Denso NLA 7/13 ... 96 1996 Lexus SC300 Crank Position Sensor Denso Includes Pigtail.

This is theinstruction on how to remove door panel of Toyota camry 1. Openthe door as wide as possible and roll the window up completely. Locate andremove five screws and two clips in the door panel. Two screws are located atthe rear of the panel, another two are located under the arm rest, one near thelight and the other in front of the light. The last screw is located in thefront of the arm rest behind a triangle shaped plastic panel, directly belowthe door handle. Pry this panel up with a flathead screwdriver to remove thescrew underneath. The two clips are near the front of the door and are smallplastic circles. Push them in with a small screw driver and pull them out. 2. Remove the plastic trim around the doorhandle. Use a flathead screwdriver or prying tool to pop the plastic out fromthe door panel. Wiggle it around until it comes loose from the door handle. 3. Use a flathead screwdriver or prying tool atthe bottom edge of the door. Pry away from the door until the clips under theedge pop out. These are plastic clips under the edge of the bottom and sides ofthe panel. Gently pop them out from the entire door panel. The top of the panelis held in place by the window trim. Move the panel back and forth until it isfree from the window trim. 4. Unclip the wire connectors and wires with aflathead screwdriver. The door panel is now free from the door.

hi ,have a look here Lexus Workshop Manuals
please rate me if useful.thanks

if the glass is broken or need it replaced. You need to remove the door panel approx. five phillips head screws, remove the triangular plastic cover in the corner or the window. Remove the 3 ten mm bolts, if electrical mirror then disconnect and replace. The screws to remove the door are behind the handle, you need to pop uo the window control panel in the door and then search for the other screws. There are many clips along the door panel so some slight pulling is needed.

USUALLY POWER WINDOW PROBLEMS ARE ONE OF THREE THINGS. 1. SWITCH 2. MOTOR 3. WINDOW REGULATOR. THE MOST COMMON PROBLEM THE LEXUS HAS IS THE MASTER SWITCH IN THE DRIVERS DOOR. IT CAN ALSO AFFECT THE OPERATION OF THE PASSENGER DOOR SWITCH....IF WINDOW REGULATOR IS BAD YOU WILL HEAR SOME CRAZY NOISES COMING OUT OF DOOR PANEL...VERY OBVIOUS.... FOLLOW THIS CLOSELY...STARE AT A LITE DOME LIGHT USUALLY WITH DOOR OPEN...WHEN YOU PRESS WINDOW SWITCH, IF THERE IS ANY DIMING OF DOME LIGHT....MOTOR IS BAD. IF DOME LIGHT STAYS THE SAME BRIGHTNESS... SWITCH IS BAD... EXCEPT IN THE CASE SOME HACKER HAS BEEN IN THE DOOR PANEL BEFORE ...IT DOES TAKE A SPECIAL TALENT TO REMOVE DOOR PANELS WITHOUT BREAKING THINGS AND EVEN MORE TALENT TO REPLACE WINDOW REGULATORS

will need both motors and regulators if you are getting power to the window motors.

sorry this is all I got. (sounds like your regulator is going/gone).

A) Remove the screws in the following locations:

1. Door handle
2. door grip
3. Middle of panel, 3/4 down the panel from the top

B) Removal of door Handle

1. Use caution
2. Slide the door handle in the direction of the motor
3. The door handle is now freed from the door

C) Partial removal of door panel

1. Insert a dull instrument into the port that is located on the panel roughly half way down the panel and the side the furthest from engine.
2. Carefully pry the panel loose.
3. With your hands, remove the panel by its contour. There are roughly 10 or so plastic plug

D) Tricky Part; Removal of door Handle

1. Free the door handle from the panel, by carefully pushing it through the panel on an angle...
2. You can now push the panel up beyond the door lock button.... then...
   
3. The wiring haness is now exposed.

E) Wiring Harness

1. You now un plug the wiring harness from:

• Door handle
• Lower courteosy light
• Electric window controls (three wires)

F) Final steps

• Lift the panel up and over the door lock button.

Now to your window problem.

When I examined the problem that I had with my Odyssey, I found the following:

1. Two bolts were missing;
2. The other tow bolts were lossed;
3. The motor had shifted positions.
   

it is under the vehicle, driver side, below the seating area, in front of the rear wheelwell, mounted on chassis in fuel line.

no, its very different