Hi what is the torque setting Nm for the cam cap bolts on a Hyundai Gatz 1.6 16valve double overhead cam engine G4EDA59 Thanks Glenn

1. First, tighten all the bolts to 25 Nm (18 lb-ft).
2. Tighten all the bolts to 50 Nm (37 lb-ft) in sequence, starting from the center and working outward.
3. Tighten all the bolts to 70 Nm (52 lb-ft) in sequence again, starting from the center and working outward.
4. Finally, tighten all the bolts an additional 90 degrees in sequence again.

Please note that it's important to follow the correct torque sequence and to use a torque wrench to ensure that the bolts are tightened to the correct specifications. It's also recommended to replace the head bolts with new ones to ensure proper torque and head gasket sealing.

The torque specification for the rocker shafts on the 2001 Hyundai Accent with the 1.5L single overhead cam engine is 18-20 lb-ft. The proper torque sequence is as follows:

1. Tighten the bolts to 8 lb-ft in a crosswise pattern.
2. Increase the torque to 15 lb-ft, again in a crosswise pattern.
3. Finally, tighten the bolts to the full torque of 18-20 lb-ft, again in a crosswise pattern.

Make sure to use a torque wrench and follow the sequence carefully to ensure proper tightening and prevent damage.

1. Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values:

• • Step 1: All to 34 Nm (25 ft. lbs.)
  • Step 2: All to 68 Nm (50 ft. lbs.)
  • Step 3: All to 68 Nm (50 ft. lbs.)

CAUTION: Do not use a torque wrench for the following step.
Step 4: Turn an additional 1/4 turn

• Step 5: Install and tighten bolts (1-10) in sequence shown, to 41 Nm (30 ft. lbs.) .

1. Tighten bolts (1-10) again to 41 Nm (30 ft. lbs.) PLUS 1/4 turn in sequence shown.
2. Install main bearing bedplate to engine block bolts (11-20), and torque each bolt to 28 Nm (20 ft. lbs.) in sequence shown.

Connecting Rod Cap Bolts 54 Nm (40 ft. lbs.) + 1/4 turn
1997 Jetta: Torque settings..vw..the head, fly wheel, big ends.


1997 Jetta3 1800 feul injection


Vibration Damper/belt Pulley
Tighten 20 Nm (14.8 ft lb) Crankshaft Toothed Belt Sprocket Tighten 90 Nm (66 ft lb) + 90° Camshaft Sprocket Tighten 80 Nm (60 ft lb) Main Bearing Cap
Tighten 65 Nm (48 ft lb) FLYWHEEL TORQUE
Torque 60 Nm. (44 ft. lbs.) + 1/4 turn (90°) [1] [1] Always replace bolts.
CYLINDER HEAD TIGHTENING TORQUE [1] :
1st sequence: 40 Nm (30 ft lb)
2nd sequence: 60 Nm (43 ft lb)
Final sequence: plus 1/2 turn (180°)
Here are some additional specifications, thanks
ntake Manifold
Mounting Bolts 25 Nm (18 ft. lbs.) Bearing Cap Nut 20 Nm (15 ft. lbs.) Rod Bearing Cap
Assembly
Tighten 30 Nm (22 ft lb) + 90° To measure radial clearance
Tighten 30 Nm (22 ft lb) but NOT additional 90° TIGHTENING SPECIFICATIONS
Oil Pump Bolt 20 Nm (14 ft. lbs.) Oil Tube To Block 10 Nm (7 ft. lbs.) Exhaust Manifold to Cyl. Head 25 Nm (18 ft lb) Exhaust Manifold to Front Exhaust Pipe 40 Nm (30 ft lb) Water Pump
TIGHTENING SPECIFICATIONS
Cover Bolts 10 Nm (7 ft. lbs.) Mounting Bolt and Studs 20 Nm (15 ft. lbs.) + 1/4 turn (90°) Pulley Bolts 25 Nm (18 ft. lbs.)

TIGHTENING SPECIFICATIONS
Connecting Rod Nuts:
Tighten In Two Stages:
First Stage 30 Nm (22 ft. lbs.) Second Stage turn an additional 90°(1/4 turn)

renew bolts
stage1- 30NM
stage2-90deg
stage3-individually slacken off 360deg
stage4-30NM
stage5-90deg

crank pulley bolt-142NM
cam sprocket bolt-88NM

i like to help people like you that give engine codes it makes it so much easier

I hope this picture helps.

Follow these steps to adjust to the recommended torque:
1. cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
2. mains-30nm +65deg
3. big ends- 1 - 26nm 2 - 52NM
4. fly-wheel -130nm
5. cam-sprocket - 100-120
6. crank-pulley - 170-180
7. cam caps -15nm

Hi there:Check this image for cylinder head bolt loosen and tighten sequence-1.5L (VIN K), 1.6L (VIN R), 2.0L (VIN F) and 1996-98 1.8L (VIN M) engines




Specs: 2.0L (VIN F) and 1996-98 1.8L (VIN M) engines- Tighten M10 bolts to 22 ft. lbs. (30 Nm), plus 60-65 degrees, plus 60-65 degrees. Tighten M12 bolts to 26 ft. lbs. (35 Nm), plus 60-65 degrees, plus 60-65 degrees.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Here's what the shop manual states:

30 Nm (300 kg.cm, 22 lb.ft)+90°+Release all bolts + 30 Nm(300kg.cm, 22 lb.ft)+90° In this instance you don't have a 'Torque to Spec"... you have a "torque to YIELD' In this specification, initially torque the head bolts to 22 lb ft... then turn each and additional 90°, then loosen each and REDO to the same specification = 22 lb.ft)+90° (you're actually crushing the head gasket TWICE and stretching the head bolts TWICE.

dear friend:here follows the settings in need:
cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
mains-30nm +65deg
big ends- 1 - 26nm 2 - 52NM
fly-wheel -130nm
cam-sprocket - 100-120
crank-pulley - 170-180
cam caps -15nm