Question about 2002 Mitsubishi Lancer

1 Answer

I need instructions on how to install a tacho in a 2002 cg lancer

I need instructions on how to install a tacho in a 2002 mitsubishi lancer

Posted by on

  • joe_d_grillo Aug 22, 2009

    its a 2 litre engine and was build in june 2002

  • Philip Armitage May 11, 2010

    not very hard job. Just need to know what engine and build date for proper tach hookup.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

We had tacho installation problem with out 98 lancer with no tacho on the panel. we got a aftermarket one but when we had to wiring it up it needed a tacho signle from the ignition coil. The ignition coil is built into the distributor which made it hard. The 2002 is the same distributor setup as the 98 so you can get step by step instructions with diagrams and pictures from my page, you will see an link that says Mitsubishi Tacho installation. website is www.sureyya.biz let me know if you find it useful.

Goodluck

Posted on Aug 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 lancer 1.5 auto. Tacho works fine when car is not moving but jumps around when driving. I put it up on blocks and put it in Drive and took it up to 100kph and it works fine. Any thoughts please.


The problem is most likely play in the line. The line that goes to your tach has a moving (spinning) cable inside. When the car is on blocks there are no restrictions, just spinning tires. When driving you are pulling the vehicle. There will be slight variations of resistance when driving. Replace the tach line and it should be fine. Not replacing it will not harm your car. It will only hamper your ability to know the rpms when driving.

Jun 10, 2011 | 2002 Mitsubishi Lancer

1 Answer

What do you mean cluster contacts bad !Whats the solution?


Remove the speedometer head unit, and check the soldered joints on the back. It's a common problem with these and some Chrysler products. "Randomly" is when the crack closes and makes contact, like if you hit the top of the dash and it starts working again. The speedometer head cluster.

Feb 24, 2010 | 2002 Mitsubishi Lancer

1 Answer

I hae a 2002 mitsubishi lancer I need wiring


Here is a link that should help you get the wiring colors you asked for. Good luck and hope this helps. http://www.installdr.com/Harnesses/Mitsubishi-Wiring.pdf

Oct 28, 2009 | 2002 Mitsubishi Lancer

1 Answer

2002 mitsubishi lancer es manual


eBay has these manuals available. Item # 270544305731
Sells for 6.99 to 7.99 + .99 for shipping.

This is the repair manual and is a CD for use with a PC.

They have owners manuals for some models too.

good luck

Oct 02, 2009 | 2002 Mitsubishi Lancer

1 Answer

99 lancer,speedo tacho n gauge problem.


probably burnt or cracked circuit board on back of gauge cluster

Jun 21, 2009 | 2002 Mitsubishi Lancer

2 Answers

2003 Mitsubishi Lancer


so u have a CH/CG lancer

you would need to remove the two 10mm bolts from the coil packs and leads and then stick the smaller version of spark plug socket in remove them, bear in mind if u have a mivec motor the spark plugs MUST be Platinum :)

Oct 21, 2008 | 2003 Mitsubishi Lancer

3 Answers

1997 CE Lancer speedometer


i had the same problem on my g/f's 2000 lancer GLXi, (with tacho),
i fixed the problem by putting a jump wire on the back of the instrument cluster,
the fault was in the wiring to the tacho part & i drew up my own wiring diagrams for the cluster unit,
then traced the fault,
looking @ the back of the cluster unit, the top right hand screw for the speedometer,,, follow the track on the circuit-board, there is a link wire UNDER the board (there is a dotted line on top where it goes, i think its the left 1,,, there is 2) this track then goes to the bottom left screw on the tacho,,,
i soldered a small gauge wire from the bottom of the link solder joint (MAKE SURE ITS THE CORRECT LINK, THERE IS 2 SIDE BY SIDE) to the bottom right track on the vertical plug socket (its common pos for the warning lights) this is where the "MIRAGE" & other "CE LANCER" (without tacho) gets its speedometer & gauges power from,

kind regards waz
if anyone needs a photo i will pull out the dash again lol its only 6 screws

Jul 17, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
2002 Mitsubishi Lancer Logo

503 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...