I replaced the starter on my 2004gmc envoy xlt 4.2liter and a tube underneath near center of vehicle came off it has around plastic end need to plug in

code P0753 (1-2 clutch solenoid circuit). Open solenoid causing the problem. Pull side cover and install new solenoid.

Do you mean your looking to drain the refrigerant (R134a) from the A/C system?
If so there is no drain plug. you will need to find a garage that has an A/C recovery/recharge machine & have it recovered before you can open the system.
If you are looking for the evaporator water drain tube it comes out of the firewall near the center on the passenger side of the car. you can see it from underneath the car. it has no plug though unless of course you've been driving many dirt roads, then it can build up a "Plug" of dirt on the end of the tube that can block it.

on my 2010 ford escape XLT i found the keyless entry code printed on a label on the smart junction box which is inside the center console. To get to the smart junction box follow these instructions.
1. with a non-marring tool(i used a putty knike wrapped in plastic wrap), pry up the chrome trim piece around the shifter.
2. Remove the storage tray from underneath the center console armrest and leave the armrest cover open.
3. Grab the center console finish panel near the cupholders and pull straight up.
4. Pull the finish panel up and back then set it aside.
5. The smart junction box is to the right and slightly ahead of the gear shifter. There should be a label with a bar code that says FoMoCo. In the corner of this label is a 5 digit number. This is the factory code.
Hope this helps.

Should be 22" for the fronts. All of the brands go bad over time, I've never found one that lasts more than one season.

Hi,
Standing in front of your Corolla with the hood open ,the starter is located right below the intake manifold(curvy tube like looking ) This is in the center of the engine.
A plastic water guard underneath the car prevents you from seeing the starter from below.
That water shield will need to be removed to access the starter.
Wayne

Good day allen,
raise your vehicle high enough to slide under. make sure you support the vehicle when raised.
Now some voyagers have a plastic shield underneath for protection. Remove this shield.
Remove the positive from the battery, Make sure all your tools are near you. remove the wires from your
starter and take note how the are seated. With a ratchet, remove the two bolts.that hold the starter in place
Sometimes there is a shield near the Tranny/Motor which needs to be remove before you remove the started
When you get the new starter reverse this this letter

It is fairly simple although I still recommend you get the Haynes repair manual on your vehicle. 1. Disconnect the Negative terminal on the battery. 2. jack up the vehicle and support the vehicle with jack stands. 3. Remove the 2 to 3 retaining bolts, there are always 2 but on some year models they put 3 you will see them. Be careful that you don't let it drop so far it breaks the wires. 4. Remove the wiring connectors. Reverse the process to install the new starter.

It was a huge pain doing this without instructions. Here is what I learned from trial and error.
Disconnect the battery, of course
To access the starter, you will need to remove the lower right exhaust.
To accomplish that, place a hydraulic jack under the 4wd transfer case and remove the cross-member (4 vertical bolts in the mount, 2 horizontal bolts on each side, and 4 vertical bolts on each side underneath hold up the cross member). Lower the drive train a bit so you can reach around the transmission to unplug the 2 right-side O2 sensors (to see what the plug looks like, look at the rear left-side of the cross-member).
Cut the exhaust in half (in the middle of the vehicle), remove the bolts from the muffler, and the right manifold. You may also want to loosen the left manifold bolts. (make sure you have extensions, a breaker bar, and some penetrating oil). You may need to raise the drive train again to get the section of the manifold out. Once that is out of the way, take the 2 bolts out of the starter, and the sockets to remove the wires should be 8mm, and a deep 13mm. You may need a special folding ratchet to get to the other side of the starter.
To put the exhaust back together again, cut about a half inch more from the place you cut the exhaust and piece it together with a 2-1/2" coupler and clamps from Autozone.

There are two crankshaft sensors located Center front of the engine, near the base of the engine oil dipstick tube.
Access is from underneath the car.
You will need to remove the plastic splash guard.
The sensors are held in by one bolt each.

If you look under the vehicle on the side where you fill the gas, The fuel lines run from the fuel tank along the edge of the vehicle, right under the side of the vehicle. The fuel filter is located along that line.. Good luck.. These tend to be very rusted and a pain to replace. Please give me a good rating, it means a lot to me.... Thank you