There are no replaceable wires in the MAF there are Two very fine wires in the MAF that can be carefully cleaned using a Q-tip and carb cleaner just spray the Q-tip with carb cleaner then gently move it up and down on both sides of the wire. The honeycomb screen on the front can be removed by removing an internal snap ring. I hope this helps. Take care.
SOURCE: bad knock sensor on 1998 chevy malibu 2.4L
The knock sensor is on the back side of the engine near the trans. It is round, with a 1 wire connector. You will have to get it from underneath. Good Luck.
SOURCE: I need info on how to replace the headlamp bulbs
The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the
headlamp to be removed.
SOURCE: Change headlight on 2008 Chevy Malibu
Hi there,
Well first you can please follow the below steps -
1. Make sure the ignition key is in the off position and the headlight switch is off. Release the hood latch.
2. Open the hood and locate the top of the headlight assembly where you intend to change the headlight. If a plastic shroud is present, locate the center bolt and remove it with a ratchet and a socket. Lift the shroud out of the way to access the headlight assembly retaining brackets. Some later models may feature a snap-release shroud requiring no tools to remove.
3. Locate the brackets on the top rear of each side of the headlight assembly. Lift them all the way up to align the hole on the bottom of each bracket to the retaining tabs on the assembly.
4. Pull the assembly forward away from the Malibu, but be careful not to scratch the bumper. There are three guide pins that require unseating. The guide pins are what aim the headlights and it may take some wiggling to get the pins from their seats.
5. Support the assembly with one hand and then reach behind the unit with the other. The low beam bulb is on the outside, the high beam bulb is on the inside. You can also replace the parking light if desired. Locate the wire harness connection. Un-clip the wire harness from the back of the bulb socket. Remove the bulb by turning it counterclockwise 1/3 of a turn to align the release tabs of the ring and the assembly. Wiggle the bulb out of the assembly.
6. Place the latex gloves on your hands before opening the package of the replacement bulb. Oil in our skin can damage the glass bulbs of halogen headlights.
7. Carefully insert the new bulb into the ring and then align the tabs of the ring to the tabs of the headlight assembly. Push inward and then twist clockwise 1/3 of a turn to lock the bulb in place. Reattach the wire harness. Rest the headlight assembly inside its cavity and test the operation of the headlight before securing the headlight assembly in place. Be sure to turn the lights and ignition back off.
8. Align the three guide pins to their seats and push the assembly back into them gently until they snap into place. Replace the retaining brackets by pushing them downward to lock into place. Replace shroud, if applicable. Remove the tools and old bulb and close the hood. Post comments for further help or information......
Good Luck!!
SOURCE: I have a 2008 Chevy
{: ) Code P0010 refers to a fault at the Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1. This code will set if the ECM (Engine Control Module) detects that the commanded state of the driver and the actual state of the control circuit do not match for greater than 3 s.
The service procedure requires close monitoring with a scan tool. Well it may be too technical for you, but simply put, it may require replacing the CMP actuator solenoid valve if it fails the component test. If the component is found to be okay, the circuit and wirings should be checked for possible shorts or open, and also the signal performance. If all circuit tests proved normal, a replacement ECM may be recommended.
If the engine light and code is consistently present, most likely it's the actuator solenoid valve. Check it out with your trusted mechanic. Goodluck.
SOURCE: 2008 chevy malibu.light clunk from front left of car.
I am a technician at GM, I replace the front shocks with monroe sensa-Trac and the sound of knocking at the front is gone
Left Front Sensa-Trac Strut 72200
Right Front Sensa-Trac Strut 72199
21 views
Usually answered in minutes!
×