I lost one of my bolt for my booi country collection 3 in 1 the one to hold up one of the side where can i get one from pleases

Question edited to add maker.
Question moved to model category.

On a 2008 Chrysler Town and Country engine 3.8 where is the fuel filter located? Hi D9Dozer, The fuel filter is positioned in the line leading from the gas tank to the engine. Please visit https://www.kbb.com/maintenance-schedules for information about recommended mile maintenance.

2008 Chrysler Town & Country Fuel Filter Replacement Prices ...

Kelley Blue Book https://www.kbb.com > chrysler > fuel-filter-replacement

2008 Chrysler Town & Country "fuel filter" Questions

Fixya https://www.fixya.com > search > fuel_filter
The fuel filter is to the passenger side and above the fuel tank. You will have to loosen the two bolts that hold the fuel tank up to move the tank down ... People also ask

goes with bolt sample.

It's not quite as simple as it seems. There are multiple hidden bolts and the plastic diverter to the passenger's side floor board is attached to the lower cover. It's a tedious process but the whole cover should be removed. Upper and lower. It's pretty much the only way to get to the 8 mm bolts on the inside that hold the diverter/door into place.

REMOVAL

1. Release hood latch and open hood.
2. Disconnect battery negative cable.
3. Disconnect the push-in field wire connector from back of generator.
4. Remove nut holding B+ wire terminal to back of generator.
5. Separate B+ terminal from generator.
6. Raise vehicle and support.
7. Remove the right front lower splash shield.
8. Remove accessory drive belt, refer to the Cooling System for proper procedures.

1. Remove the lower oil dip stick tube bolt (Fig. 2).
2. Remove wiring harness from the oil dip stick tube
3. Remove the 3 mounting bolts.
4. Lower vehicle.
5. Remove oil dip stick tube from vehicle.

1. Roll and remove the generator from vehicle (Fig. 3).

INSTALLATION

1. Roll and place generator in position on vehicle (Fig. 3).
2. Install upper bolts to hold generator in place.
3. Lubricate the O-ring. Install oil dip stick tube.
4. Install the upper oil dip stick tube bolt.
5. Place B+ terminal in position on generator.
6. Install nut to hold B+ wire terminal to back of generator.
7. Connect the push-in field wire connector into back of generator.
8. Raise vehicle and support.
9. Install the lower mounting bolt and tighten.
10. Install the lower oil dip stick tube bolt and tighten (Fig. 2).
11. Install accessory drive belt, refer to the Cooling System for proper procedures.
12. Install the right front lower splash shield.
13. Lower vehicle.
14. Install wiring harness to the oil dip stick tube
15. Connect battery negative cable.
16. Verify generator output rate.

remove the door panel and drill the rivets that are holding the motor and remove the nuts that hold the track the i think the track and the motor are one piece if you don't have a rivet gun you can use nuts and bolts instead

take off the door panel on the inside and you'll find bolts that hold it on under there

Remove Old Mirror
1. 1 Open the side door to the Chrysler Town & Country, and find thescrew that holds the side mirror molding in place.
   
2. 
   Take the screw out and remove the molding panel that attached around the outside of the power mirror.
   
3. 
   Remove the bolts connecting the mirror to the door assembly. If equipped, unplug the power side view mirror wiring harness connector.
   
4. 
   Unplug the electric connectors, and pull the mirror out of the molding.
   

front of motor lower end just follow from battery down the wire is red there should be 3 bolts holding it on

Remove the wiper arms (pop off the caps at the base) and the 15mm nut. Take out the screws that hold down the wind shield cowl lift it away to expose the washer hoses. Unplug the wiper motor (center driver's side) by pulling out the red clip on it and squeezing the tab. Remove the 13mm nut from the wiper motor idler arm and take out the 3 10mm bolts that hold it in place. Squeeze it out from under the wiper transmission, or loosen the lower bolts. You'll see them. Not a difficult job, just take your time.

Hope I've helped.

there is 3 10mm. bolts that hold the whole lens in they are on top ,take these out and then pull out whole assembly this will make it easy to replace sorry it took long to get back to you!