Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything
someone on fixya recommended it to me and I thank him even today
They have full manuals and it's verrrrry cheap and mine
I got free in offers
3rd time I bought it, I also had an issue with the file so the girl replaced it in 30 mins
there is one website more but i don't remember its name it was 2 years back bitman something link this
Try these out brother
SOURCE: changing fuel filter on 2002 Mazda pickup
Clean all dirt and/or grease from the
fuel filter fittings. "Quick Connect" fittings are used on models
equipped with a pressurized fuel system. These fittings must be
disconnected using the proper procedure or the fittings may be damaged.
The fuel filter uses a "hairpin" clip retainer. Spread the two hairpin
clip legs about 1/8 in. (3mm) each to disengage
it from the fitting, then pull the clip outward. Use finger pressure
only; do not use any tools. Push the quick connect fittings onto the
filter ends. Mazda recommends that the retaining clips be replaced
whenever removed. The fuel tubes used on these fuel systems are
manufactured in 5/16 in. and 3/8
in. diameters. Each fuel tube takes a different size hairpin clip, so
keep this in mind when purchasing new clips. A click will be heard when
the hairpin clip snaps into its proper position. Pull on the lines with
moderate pressure to ensure proper connection. Start the engine and
check for fuel leaks. If the inertia switch (reset switch) was
disconnected to relieve the fuel system pressure, cycle the ignition
switch from the OFF to ON position several times to re-charge the fuel system before attempting to start the engine.
Remove the "hairpin" clip retainers to access the fuel line fittingsThe
inline reservoir type fuel filter should last the life of the vehicle
under normal driving conditions. If the filter does need to be
replaced, proceed as follows:
CAUTIONIf
the fuel filter is being serviced with the rear of the vehicle higher
than the front, or if the tank is pressurized, fuel leakage or
siphoning from the tank fuel lines could occur. to prevent this
condition, maintain the vehicle front end at or above the level of the
rear of vehicle. also, relieve tank pressure by loosening the fuel fill
cap. cap should be tightened after pressure is relieved.
The
flow direction arrow should be positioned as installed in the bracket
to ensure proper flow of fuel through the replacement filter.
To install:
SOURCE: Location under hood for fuel pump relay on 2002 Mazda Millenia S
JUST RELEASE THE PRESSURE AT THE FUEL PRESSURE TEST PORT ON THE FUEL SUPPLY RAIL THAT SUPPLIES THE INJECTORS, IT IS A METAL VALVE LIKE A TIRE VALVE, THAT IS THE FACTORY RECOMMENDED METHOD..
SOURCE: Failed evap test on 1995 mazda b2300
did u try hoses that go to evap canister? and the evap canister itself? Thanks, Lee
SOURCE: mazda b2300 electric fuel pump no working
pumps are rare to fail on these. the quick easy thing to check is the inertia switch. if in a wreck or jarred hard, this switch shuts down the fuel pump to stop a fire and must be manually reset. it is located behind the lower kick panel on the passenger side of cab interior. its a little black switch with a red button facing upward. if tripped the button is up. push back down and it will re-engauge. try to start may have to crank alittle to prime. this procedure is in your owners manual too if need be.
SOURCE: Where is the fuel filter on a 1994 Mazda b4000 pickup?
Driver side frame rail right where the door is. It's held in by a large hose clamp. It has 2 white plastic clips . 1 on each hose of the filter. When removing have a container that can hold gas ready because about a pint of gas will come out. Make sure new filter comes with new clips. I don't recommend using old ones. After new one in place turn key on and leave in run position for 20 seconds so filter can gill with fuel before starting and inspect fir leaks.
183 views
Usually answered in minutes!
×