Question about Cars & Trucks

1 Answer

Will the crank sensor get the car started if it just crangs but doesnt fire

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 104 Answers

Yes and no, if it is the crank sensor you will have implausible signal for ECU. Check spark at plug, Check fuel delivery pressure,
Check scan tool codes.

Posted on Jun 03, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
davesmith_37
  • 94 Answers

SOURCE: the car will crank but does not have fire going to the coil pack

did you do a spark test?
This could be a number of things, your crankshaft sensor, coils or ignition module.
check the coils

  1. Remove the ignition coil(s).
  2. Using an ohmmeter, check the resistance between the primary terminals on the underside of the coil. The resistance should be 0.50-0.90 ohms.
  3. Check the resistance between the secondary terminals. It should be 5,000-10,000 ohms.
  4. If the coil failed either test, replace the coil.

Posted on Aug 01, 2009

  • 8 Answers

SOURCE: Car was running well then just refused to

its possible there are multiple coil packs usually one for each bank or one for every two cylinders. Or check for a ignition control module

Posted on Oct 08, 2010

  • 145 Answers

SOURCE: Car wont start. Engine is cranking but not firing.

The Electronic Ignition switch also called the may have failed.

Posted on Dec 29, 2010

  • 3640 Answers

SOURCE: car wont start. it

have you pulled a spark plug to see if they are getting wet with fuel? Have you got power to the ignition coils with the ignition switch in the on position? The coils get power and are then grounded by the ECU. if power to coils, then replace coils.

Posted on Sep 05, 2011

  • 439 Answers

SOURCE: trying to change the crange

No there is nothing holding the sensor from the inside.

Posted on Feb 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine light doesnt come on when key is turned on,cranks but will not start.no fire no fuel


Take to car to a diagnostic center, and they will attach a diagnostic machine to the car to see if it's the onboard-computer that's malfunctioning.

If the fuses are all OK, and the starter cranks the engine, but there's no firing, the diagnostic system will tell the tech what it is, there are various reasons there's no firing when the engine cranks,

Someone may say check the disable switch on the transmission, but if that's broken, the starter will not crank the engine.

Jul 09, 2014 | 2003 Kia Optima

1 Answer

P1200b code 97 malibu


I would suggest that the cam sensor doesnt do much and the crank is the predominant one here. P1200b is the injector circuit. Try checking all wires to injectors and the harness connectors. If it jumped it's timing perhaps or the crank sensor was broken or bad it will not fire or fire erronously.

Jun 02, 2014 | 1997 Chevrolet Malibu

2 Answers

P0335 hard starting


that trouble code indicates that crankshaft position sensor circuit has a fault.
check that the 3 wires on the sensor are in tact and area around it is free of oil and deposits
it that doesnt work then you will need a new sensor

May 07, 2012 | 2001 Volvo V70 XC

1 Answer

2000 chevy s-10 died on highway will crank will not turnover bought new battery


spray brake cleaner into throttle body and try to start. If it starts your fuel pump failed most likely. If it doesnt fire most likely crank sensor or ignition module failed.

Jun 16, 2010 | 2000 Chevrolet S-10

1 Answer

Engine turning over and firing but wont start. timing chain looks good, has new crank sensor, o2 sensors, and cat.


check wiring, fuses and relay for fuel pump and check fuel filter---also recheck to crank sensor wiring ,connections and sensor new doesnt mean not defective

Feb 10, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

2002 pt cruiser dies then fires right back up randomly going down the highway


most of the times when the car cut out it is cause by the crank angle sensor you wait for it to cool down and it will fire back up again, best way to check it is to take a bottle of water with you and try to locate (which is between the fire wall and the engine on the driver side on the engine block) where the crank angle sensor. when the car cuts out pour the water on the sensor to cool it down if the car then starts right away that is the problem.

Oct 28, 2008 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22108 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...