Removing handle that when installed went click, need to remove handle to return

To remove the freezer door handle on a Westinghouse WHE5100SA-D, try the following steps:

1. Look for a small plastic or metal cover on the handle. This may be located on the underside of the handle or on one end. Use a small flat-head screwdriver to gently pry the cover off.
2. Once the cover is removed, you should see a small screw or bolt holding the handle in place. Use a screwdriver or socket wrench to loosen and remove the screw or bolt. Be sure to hold onto the handle as you remove the screw/bolt, as the handle may come loose at this point.
3. After the screw/bolt is removed, you should be able to lift the handle off of the door. If it does not come off easily, try gently wiggling it back and forth until it loosens.
4. Repeat these steps for the other handle if necessary.

If you are still having trouble removing the handle, consult the owner's manual or contact Westinghouse customer service for additional guidance.

You must remove the door panels and check for a disconnected lock release rod.

Kindly check the winder handle if OK. If fine you need to check the winder unit by removing the door panel. Possibly the teeth of the unit is worn out and also check the return spring.

buy a new handle for twenty bucks.

I have a damaged Hyundai I30 door can I just replace the outside shell of the door ?

the cable from the door handle to the door lock has either broke or the plastic retaining clip has snapped ,either way take the door panel off and have a look to verify exactly what is wrong

Technical Instructions
See picture below
1. Remove door trim panel and water shield per
NOTE: Place a strip of masking tape along the edge of door before removing trim panel to prevent scratching the door with the trim panel removal tool.

2. Snap cable housing end from slot on inside door handle assembly and disconnect cable.
NOTE: Use care to prevent bending of cable housing retainer bracket.

3. Remove rear window channel retaining bolt to allow access to door latch.

4. Position a block (screwdriver handle) between the latch and the door inner panel and snap the cable housing end out of slot (towards inner panel) on door latch assembly and disconnect cable at latch.
NOTE: Use care when removing cable housing to avoid bending of the latch. Discard cable.

5. Hook up new cable at latch and snap cable housing end into slot.
NOTE: Make sure the cable housing is fully seated in the slot.

6. Apply a light film of Teflon grease to the barrel end of the cable. See Figure A.

7. Install return spring. See Figure A.
NOTE: Ensure that the push button rod is located between the spring and the door inner panel.

8. Install foam block at latch. See Figure A.

9. Position water shield over the return spring and install push pin to retain upper portion of water shield. See Figure B.
NOTE: Push pin goes in the same hole as the return spring.

10. Clean hands of grease before performing step 11.

11. Remove protective backing along the lower edges only of the water shield. See Figure A.

12. Install latch water shield at door latch. Pinch the exposed adhesive surfaces together to secure the water shield. Check to insure water shield is not showing through the door shut-face latch access hole. See Figure B.

13. Attach cable to inside door handle assembly and snap cable housing into slot.
NOTE: Make sure the cable housing is fully seated.

14. Check the gap as shown in remote control using a 3/16 drill bit shank end. The drill bit shank should fit in the gap without any clearance and a tight fit is preferred. See Figure C.

15. If the drill bit is too loose or does not fit, adjust by bending the cable bracket as required.

16. Place plastic wedge on remote bracket as shown. Wedge must fit with at least a light press fit for retention. See Figure D.

17. After installation, Apply a dab of special Teflon grease, supplied with the service cable to cable housing openings at inside handle end. The grease should surround and contact the cable all the way around, to seal the opening between the cable and the cable housing.

18. Check all latch functions to insure correct assembly of latch system. If the inside handle does not release properly, replace the inside handle remote release mechanism.

19. Reposition and install trim panel using new push pins if required.

This is a manufactures bulletin


SUBJECT:
Inoperative Right Front Door Switches OVERVIEW:
This bulletin involves replacing the right door interior handle. The loss of ALL functions may occur when attempting to control them from any of the switches located on the right door due to electrostatic discharge through the right door interior handle. The right door interior handle must be replaced to protect the switch module from static electricity. The new handle is more resistant to electrostatic discharge. MODELS:
2004 - 2008 (CS) Pacifica SYMPTOM/CONDITION:
The vehicle operator may experience a permanent loss in ability to actuate ALL of the following functions from the right door switches: ^ Power door locks. ^ Right power mirror. ^ Right power seat adjustments. ^ Right power window control. ^ Right heated mirrors. ^ Memory functions associated with the listed systems on right side (if applicable). ^ Loss of communication with the right door switch module to Scan Tool: DIAGNOSIS:
Perform a "Hard Reset of the right door switch module. This may be accomplished by removing all power (including memory keep alive power) from the right door switch module by unplugging the module power connector. Alternatively, vehicle power may be interrupted by removing the negative battery terminal when the ignition switch is in the OFF position. If after performing the hard reset functions of the right door switches return perform the Repair Procedure.


PARTS REQUIRED:
REPAIR PROCEDURE:
1. Disconnect the negative battery cable. 2. Remove the right door trim panel
3. Remove the door tweeter speaker. Refer to the service information in TechCONNECT. Refer to 8 - Electrical > Audio > Speaker > Removal (Fig 1). 4. Remove the power seat switch. Refer to the service information in TechCONNECT. Refer to 8 - Electrical > Power Seats > right Seat Switch > Removal. 5. Replace the right door interior handle, p/n 05170261AA, as described on Mopar Instruction Sheet K6855628 included in the handle kit. 6. Install the power seat switch. 7. Install the door tweeter speaker. 8. Install the right door trim panel. 9. Connect the negative battery cable.

The window perhaps came out of the channel, to check and/or repair you must remove the door panel after removing the door handles, window handles, etc. IF this is the case after you get inside, most are usually Nylon bearings, which must be replaced or perhaps channel alignment is off, lets hope for your sake...A special tool is needed to remove the above mentioned handles.