Question about Subaru Cars & Trucks

Open Question

Does anyone know what the torque specs are for a 2006 subaru impreza engine to trans bolts? I have been looking, but cannot find any specs.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

Ad
  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

chuck943
  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

terseo
  • 92 Answers

SOURCE: torque specs for 1998 tercel 1.5L

Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.

Hope this helps

Posted on Sep 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What year manual transmission fits to a 2004 Subaru Impreza WRX?


Pretty much any "EJ" transmission will fit any "EJ" engine, the only problems are whether the clutch is a pull or push type release bearing? That will also make a difference how the clutch slave cylinder mounts up. If it isn't a turbo model trans, it will not take the HP that the engine puts out for very long. The Impreza STI manual trans will bolt up, but there will be some exhaust fitment issues where the down pipe bracket connects to the trans.

Sep 09, 2014 | 2004 Subaru Impreza

1 Answer

2009 Subaru 2.5L Bolt Torque Specs


Pick up a repair manual. It will have the 30 or 40 different torque specs in it. IE head, intake, exhoust, rocker shaft, timing gears, etc, etc, etc.

Sep 04, 2014 | 2009 Subaru Forester 2.5

1 Answer

Striped the nut on the rear strut just need to know the specs so i can get a new one dealership wont help


Hello,

Subaru always states in their service manuals to replace all self locking nuts with new hardware, never reuse old nuts.

Tightening torque for the 3 nuts that fasten the strut to the body: 20 N-m (14.5 ft-lb)

The main strut rod nut torque spec is: 55 N-m (40.6 ft lbs)

Jul 30, 2011 | 2008 Subaru Impreza Wrx

1 Answer

Please i want to know my subaru impreza 2006,s diagnosis code numbers


Here is a list of Subaru diagnosis codes. If these are not what you are coming up with let me know the numbers you are getting and I will look them up on my genisys scanner to further assist you.
1111 No codes stored
11 Crankshaft position sensor (Don't confuse with above, usually when the crankshaft sensor if dodgy the thing won't start anyway)
12 Starter switch faulty
13 Camshaft position sensor
14 Injector no.1
15 Injector no.2
16 Injector no.3
17 Injector No.4
21 Engine temp sensor
22 Knock sensor
23 Mass air flow sensor
24 Idle air control sensor (usually accompanied by running too fast/slow)
31 Throttle position sensor
32 O2 sensor
33 Vehicle speed sensor
35 Emissions canister purge valve
38 Torque control signal (Automatics)
42 Closed throttle position
44 Turbo wastegate regulator malfunction
45 MAP sensor
49 CO adjustment resistor for older cars not fitted with cats
51 Neutral switch (Manual gearbox)

Feb 08, 2011 | 2007 Subaru Impreza WRX STI Limited Sedan

1 Answer

My 06 Subaru Impreza WRX is giving me a P0021 code check engine light. I want to change the variable valve timing sensor and the timing belts. Where can I find the information on how to do this?


I stand behind All-data its a program that will give you a break down on everything, it also gives you torque specs with sequences technical service bulletins, and safety recalls there's nothing you cant do with this at the helm. Go to Alldata.com I think its 14.95 for the year but the skys the limit good luck

Apr 16, 2010 | 2006 Subaru Impreza

1 Answer

What are the clyinder head bolts torque wrench settings for a 1994 subaru impreza wrx


Impreza torque settings MUST be done in the correct sequence,its critical when re building.
If you have a local garage who are friendly with, ask if they have autodata.If so they can print you a torque sequence and settings.

Nov 10, 2009 | 1996 Subaru Impreza

1 Answer

Torque specs for truck bed mounts


Torque specs are not important in this application, apply some thread locking compound and tighten the bolts.

45-60 ft lbs is about right for the size bolts that are used on that box.

Sep 22, 2009 | 2006 Chevrolet Colorado

1 Answer

The Subaru impreza will start but will not go into gear. has


sounds like internal trans leak ,fluid pressure bleeding down in trans,loss of fluid pressure means no go,check valve for torque convertor may also be bad,hopefully fluid has been checked ,does trans control unit store any codes?

Jul 17, 2009 | 2005 Subaru Impreza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

Marvin
Marvin

Level 3 Expert

85104 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...