Question about Cars & Trucks

Open Question

The bearing on mid-drive shaft which h way does it turn to loose

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 71 Answers

SOURCE: Remove the Center Support Drive Shaft Bearings

use a cutting wheel and cut through the bearing as far as you can without damaging the drive shaft.Then get a big hammer and a chisel drive the chisel into the cut and break the bearing.

Posted on Jun 25, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front diff.seal leaks


Remove the front drive shaft remove the drive yoke off the pinion shaft remove the old seal install new seal install front drive shaft. PS check pinion bearing play before removing drive yolk. if it is loose then you might also need bearings

Oct 21, 2015 | Ford Explorer Cars & Trucks

1 Answer

I have a leak of grease from the back of the truck between the rear tires under the truck. What could it be?


Sounds like a bad seal from pinion gear output shaft. ( if rear wheel drive ). To repair, take drive shaft off by removing the 2 u-bolts at the rear of shaft. A screwdriver is handy 2 pry shaft forward enough 2 remove shaft. This is the tricky part, the 2 bearing caps on u- joint r gonna want 2 fall out! Have a length of tape handy & run tape around the caps so u dont loose dozens of lil needle bearings. Also, ur gonna loose oil outta the rear of trans so use a pan 2 catch drippings. Next u have 2 remove nut holding rear yoke, where u-bolts were, find appro puller, remove yoke. Seal now should b avalible 4 rmoval.use seal puller, le. screwdriver&bfh, install new seal & rest is reverse order. Dont loose ur bearings,the're hard 2 find in the dirt! I kno 1st hand.

Aug 08, 2015 | Cars & Trucks

1 Answer

The front right tire on my 95 plymouth neon shakes an grinds when im going going straight or taking a right turn but only when im accelerating then stops when i press harder n the pedal. My drive shaft...


CV shafts "look" fine even when they're not. Grinding when turning or on acceleration is almost always the the CV joint. Replace the right side CV shaft. As far as the bearing being "loose", it is a pressed-on unit. I'd probably replace that too. Make sure you torque the CV spindle nu to the proper torque value. If you don't and it's too tight or too loose you will get an early failure of the bearing.

Jan 22, 2015 | Plymouth Cars & Trucks

4 Answers

What is the reason for front grinding when turning


This due to either a worn wheel bearing or a worn front drive arm.

The most common cause of a grinding noise when turning is a worn front wheel bearing. What happens is that the weight of the car is shifted on to that wheel as you make the turn causing the worn bearing to make a grinding noise.

Jun 02, 2014 | 2003 Ford Focus

1 Answer

Is a 2004 ford f-150 2wd carrier bearing.. ( mid-mount bearing ) on driveshaft replaceable, or do i have to replace entire driveshaft?


it is replaceable
normally it comes complete in the rubber mount
you will have to undo the drive shaft flange at the bearing
remove the drive shaft and take it to an accredited drive shaft repair shop or take the vehicle to an accredited drive line specialist shop
the repair will require that you place the flange back on the shaft after the bearing replacement in exactly the right position or you will get harmonic vibration after the job so talk with the experts first if you want to diy

May 09, 2017 | Gateway Cars & Trucks

1 Answer

I hear a whine noise in the rear end when sterring to the right but cant find out which bearing is bad


i will think that its the right rear,not because your turning right do i say this but because of the way bearings ride on pressure and negative pressure. see when you turn right the bearings on the right hand side will ride tight on the top and loose on the bottom. when you turn left the bearings will ride loose on the top and tight on the bottom. This is difficult to say without someone in the trunk while you drive listening for direction of sound. Also when bearings or u-joints go bad the sound can carry through drive shafts, axle housings and make it very difficult to locate. the only true way is to tear down and inspect races,axle shafts for wear.

Feb 06, 2011 | 2002 Jaguar X-Type

1 Answer

How to replace a middle bearing in drive shaft of a 1996 chev silverado 2500


Replacing the mid-ship carrier bearing is not that hard.

You will need to unbolt the U-joints, seperate the drive shafts.
Unbolt bearing retainer. Take this to a good auto parts shop that has a machine shop. Tell them you need a new one and they will do the rest.

Aug 29, 2009 | 1995 Chevrolet Silverado 2500

1 Answer

TR6 Clunking


Does it go away or change when you depress the clutch. If so you will need to inspect the clutch pressure plate and bearing. You may need to remove trans. You may have a loose bolt on the flywheel that backed off a little.

Aug 14, 2009 | 2006 Triumph Tr 7

1 Answer

1985 M Benz Sd differential s half shafts


first remove the differential half shafts and drive shaft, remove rear cap, loose the bolts on each end bearing,remove the differential assy. then replace bearings

Apr 12, 2009 | 1985 Mercedes-Benz 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22406 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...