Question about Cars & Trucks

Open Question

Yoke gasket leaking oil and how to remove without taking 2002 650 vstar engine apart

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
pal03246

Phil Lovisek

  • 726 Answers

SOURCE: 2000 Engine oil leak

most likely front cover o-ring. there is a small $4 dollar o ring behind the front engine cover, that leaks. Pretty common problem on your car.

Posted on Aug 03, 2008

Ad

Anonymous

SOURCE: Leaks oil looks like from valve cover

You have to remove the spark plugs cables and remove the four nuts that you see when the cables are removed.

When the four nuts are removed, simply raise the valuve cover. When replacing the gasket, make sure you get the gromets as well. Those sometimes get worn or crack since they are more exposed than the value cover gasket. Make sure that you clean the cover from oil and replace the gasket with no use of silicon.

Good Luck.

Posted on Aug 04, 2008

Abdi Jama

  • 119 Answers

SOURCE: 1991 Toyota Pickup Leaks oil


put new cylinder head gasket cover.clean the engine,if its check the cylinder head boltes and tight.

Posted on Sep 19, 2008

Abdi Jama

  • 119 Answers

SOURCE: 7mge have oil leak

hi if your engine 22R front engine first in side timing cover where engine bully fitted there is oil seal, next valve cover front side between cover and head there seal not like oil seal half cercle shap it makes leak also front side of the camshaft there is oil seal..

Posted on Nov 08, 2008

mrgreenz

Daniel Arellano

  • 962 Answers

SOURCE: 1996 honda prelude oil leak

did you check the steering pump, AC compression pump, etc or other engine components ? it could be something other than the engine.

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace oil pan gasket?


Do that one or get that done on a lift. If not.... drain the oil & filter, every drop. In a gentle sequence loosen remove every other oil pan bolt . Next loosen, don't remove, the rest of the & slowly take out 1 fm the ft 1 fm the rear, 1 fm the side & keep going until they are all loosen enough to totally remove. The pan may fall by its own weight, if not, a few taps with no bolts will cause it to drop. Work it off around the oil pump & float, remove the gasket when the pan is down clean the engine block of gasket & oil & reinstall the new gasket. I'm not saying your gasket isn't leaking, but I've had many requests to replace pan gaskets & the front or rear seal is leaking. Besides the fact without a lift, power tools & an oil drain, this one is a rough one. Have it Done! Good luck

Nov 21, 2015 | 1999 Chevrolet Malibu

1 Answer

Oil leak craftsman snowblower


Only a few places to leak oil from, Main crankshaft oil seal, Oil fill cap, valve cover gaskets, Cracked engine block, Engine Block gasket (some blocks split apart)

Mar 08, 2015 | Cars & Trucks

1 Answer

How do I change oil pan gasget


Jack up truck for safety sake put jack stands under frame . remove all engine oil remove all bolts holding oil pan on if their is not enough room to drop pan you may have to remove bolts holding motor mounts and jack up engine. if front end linkage is still in the way remove linkage. pull oil pan out. check gasket that was between block and oil pan if any stuck to block of engine remove with gasket scraper or wire brush or wire wheel on drill.make sure mating surface is clean put new gasket on new oil pan I like to use a high temp sealer on gasket both sides. Put pan with gasket back in place of old oil pan and tighten all bolts. jack engine down ,replace moter mount bolts replace any linkage you took apart. and dont forget to replace engine oil. make sure oil plug is in pan before pouring oil in . before starting engine check that no oil is leaking than start engine and check for any leaks again if all is good your done. if this was helpful please leave good feed back. A good temp fix on a rusted oil pan is JB weld make sure no oil is on pan clean with towel and rubbing alchol .you may have to drain oil first. if it is rusted badly you may have to use a wire brush on a drill to clean the area to patch. if patched properly it may last for years.

Oct 17, 2014 | 2000 GMC Sierra

1 Answer

Car never burned,or leaked oil till few days back.Drove about fifty mi hwy.Smelled oil burning on engine.Oil coming out oil pan gasket,And from every gasket from engine +under timing belt cover. Can it be...


It can be fixed without removing the engine. What car is it? cause it depends if its fwd or rwd, the fwd usually need the exhaust removed before removing the oil pan

Oct 05, 2014 | Cars & Trucks

1 Answer

Can I repair a bad cylinder without taking apart the motor in a 2000 Monte Carlo?


Are you talking about compression readings? If so, and you only have 30 psi, engine is in serious state of disrepair. The cylinder head will have to be taken off to fix the problem-sounds like a stuck valve, a non sealing valve, or a blown head gasket. There's no way to get to it without removing the head.
Apparently you had a compression test done? If you had done or would do a leak down test of that cylinder, it would pinpoint the source of the problem-whether an intake or exhaust valve, or a head gasket, or piston or ring damage. With a leak down test, wherever the air is escaping from the cylinder points to the source: if for instance, air leaks out the exhaust pipe, you know it is the exhaust valve not sealing in that cylinder. If air leaks out the intake-it's the intake valve.
Air hissing from the oil dipstick tube would mean compression is being lost past the piston rings-going into the crankcase.

Feb 22, 2013 | 2004 Chevrolet Monte Carlo

2 Answers

Replace gasket, oil leak front of oil pan and timing chain cover


Yes, oil commonly leaks from its valve cover gasket the only way to fix this problem is buy replacing the gaskets. -----------------------------------------------------------------------------------
car cables & obd conectors

Dec 24, 2012 | 1993 Geo Tracker

2 Answers

I have oil in my coolant tank. I was told to replace my Intake manifold gasket. I've also herd about a product called blue devil that fixes these problems without takeing apart the car? has anyone...


If you have oil in the coolant then NO, only if water was going into the oil then yes, but because its oil in coolant a repair of the gasket will be required.blue does work for coolant leakage,

May 08, 2011 | 2003 Chevrolet Malibu

1 Answer

2004 Explorer: Rear differential cover is leaking, how do I fix i...


put flat pan under the housing remove the bolts holding the cover usually 10 or 12 (1/2 or #12 metric) bolts? allow the rear end grease to drain... then scape off the old gasket clean with brake cleaner spray install either new gasket or form one with oil resistant silicone put the cover back on , dont refill the fliud for at least 12 hours if using silicone. Also check the front driveshaft rear end yoke seal....they sometimes leak making the illusion of a rear end pan cover leak...if that is leaking you remove the shaft carefully...remove the large yoke retaining nut, replace the press in seal...be sure retaining yoke nut is properly torqued when reinstalling .

May 06, 2010 | 2004 Ford Explorer

2 Answers

Oil leak after radiator change


The radiator has a transmission and engine oil cooler lines to it too. One of the oil lines are leaking, if you know which one that's have the battle. I believe the transmission line is on the passenger sides and the oil cooler line is on the drivers side. Look at where the lines connect to the radiator and see if there is signs of the leak. You may need to spray it down with brake cleaner if you not sure if it's a new leak or old leak from the accident. Good luck and hope this helps. And what do you mean by rear case gasket?? You mean the gasket that connects the transmission to the transfer case, or the rear O ring yoke gasket.

Jun 12, 2009 | 2000 Dodge Durango

1 Answer

Oil pan gasket on 740 gle station wagon.


Hmmm...I don't think the clearance on your16v engine are that much different than the 8 valve models. On them, all you do is loosen the passenger side engine mount and jack the motor up. Be sure to use a block of wood so you don't bend anything. If you have access to a hoist or can build a support to use a come-along to winch it up it makes things much easier. If fo some reason one does have to loosen the steering yoke, the couplers are down where it attaches to the cross member. There is a pinch bolt you loosen and then it will slide.
If you're losing enough oil in 45 minutes that the oil light comes on or the engine begins rattling, you have more to contend with than an oil pan gasket. OP gaskets drip, not pour. I've installed a pan w/ no gasket and not had the severity of oil loss you describe.

Apr 06, 2009 | 1990 Volvo 740

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22432 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...