SOURCE: 2005 Tucson
camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.
SOURCE: head bolt torque specs and timing marcs for a 94 volvo 960 6cyl
you do 14 foot pounds then 45 foot pounds then a 120 degree turn.if aluminum heads are what you have
SOURCE: Hi I need torque specs for b5 dohc(cylinder head job)
the pdf manual says it is 10 - 13 ft lbs
from my research it is 75 ft lbs
I hope I am right cus I just set my head at that :(
before i got the pdf file!
havent started it yet though
SOURCE: 94 mazda B3000 3.0L cylinder head torque specs
Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds
Use torque sequence below
SOURCE: need torque specs for 83 chevy 350 cylinder head bolts.
Hello there
Torque
Specs
These specs may not be correct for your
application.
Verify your engine specs with a service manual
for your year and model.
always
torque
bolts in three equal increments
Bolts or Parts
Lube or Sealer
Torque to:
7/16 Main Caps (2 bolt)
Engine Oil
70 ft-lbs.
7/16 Inner Main Caps (4 bolt)
Engine Oil
70 ft-lbs.
7/16 Outer Main Caps (4 bolt)
Engine Oil
65 ft-lbs.
3/8 Outer Main Caps (4 bolt)
Engine Oil
40 ft-lbs.
Warning!!! If you
are using ARP bolts, you MUST use
their specs. Click Here!
3/8 Connecting Rod Bolt
Engine Oil
45 ft-lbs.
11/32 Connecting Rod Bolt
Engine Oil
45 ft-lbs.
Cylinder
Heads
Engine
oil
(blind hole)
Sealer
(water
jacket)
65 ft-lbs.
Rocker Studs (screw-in)
Engine Oil
50 ft-lbs.
Oil Pump
Engine Oil
65 ft-lbs.
Oil Pan
Engine Oil
12 ft-lbs.
Cam Sprocket (upper gear)
Thread Locker
20 ft-lbs.
Timing Cover
Engine Oil
6 ft-lbs.
Intake
Manifold
(Cast Iron
Heads)
Non- Hardening Sealer
30 ft-lbs.
Valve Cover
Engine Oil
3 ft-lbs.
Exhaust Manifold
Anti-Seize Lubricant
25 ft-lbs.
Spark Plugs
No Lube or Sealer
20 ft-lbs.
Flexplate
(Automatic)
Flywheel
(Clutch)
Thread Locker
60 ft-lbs.
Clutch Pressure Plate
Thread Locker
35 ft-lbs.
Centerbolt
(Harmonic
Damper)
Engine Oil
60 ft-lbs.
Bellhousing
(Transmission
to Block)
Engine Oil
25 ft-lbs.
Head
Bolt Tightening Sequence
11,942 views
Usually answered in minutes!
×