Question about Cadillac Cars & Trucks
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.
Posted on Jan 25, 2009
First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.
Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.
Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.
Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.
Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.
The bulbs come in a two pack of cost $4.95 .
Posted on Nov 24, 2009
Raise and support vehicle.• Remove right rear wheel housing liner, see Repair Manual Body Exterior Group 66 - Exterior equipment, "Rear wheel housing liner, removing and installing" in ElsaWeb.• Disconnect T-3 electrical connector at Leak Detection Pump (LDP).• Disconnect EVAP purge line, EVAP vacuum Line and EVAP vent line from EVAP canister.
Posted on Sep 07, 2012
Open the lid fully, you should see small hold down bolt heads, maybe 7 mm...these must come completely out, be sure to label as length etc is important. There are also 2 front connectors to the lower dash, but depending on your need to remove, you may not need to remove these...you probably need to remove the gear shift knob to raise the console...look directly under the knob...sometimes a small pull out clip to release the knob, sometimes a allen head screw to release...hope this helps.
Posted on Jan 01, 2015
Tips for a great answer:
Aug 10, 2017 | Cadillac Cars & Trucks
Nov 26, 2015 | 2008 Cadillac Srx
Mar 04, 2015 | 2006 Cadillac SRX
Nov 08, 2012 | 2005 Cadillac SRX
Oct 24, 2010 | 2005 Cadillac SRX
22 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: