Question about Lexus Cars & Trucks

1 Answer

Good morning, I have a Lexus GS300 1998 and I need to change the antenna and drive motor. Can you tell me how to remove the trim inside the luggage space to gain access to the unit please? Regards

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lexus Master
  • 1,548 Answers

See link it may help

https://workshop-manuals.com/lexus

Posted on May 09, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 119 Answers

SOURCE: want to remove driver side door panel to gain access to power window motor

first remove the tweeter speker if equipped this comes off easily by gently prying from behind, then remove the small panel behind pull handle you"ll find a screw behind it\remove that,the next part is a little tricky the door grip needs to come off to achieve this place a small flat screwdriver at the top of the handle and pry forward the turn handle counterclockwise and this will release it from the clips you"ll then find 2 screws one at the top other at the bottom of door grip remove those and then gently pry from the bottom of the door panel to release the retaining clips thats it

Posted on Jul 14, 2009

emissionwiz
  • 85206 Answers

SOURCE: How do I remove the power window motor on a 1989

the motor is located at the front of the door at bottom, on the sheet metal in front of the motor u will see three dimples/indentations in the door skin sheet metal covering the motor, drill them out with a 1/2" drill bit, use a 1/4" drive 8mm or 5/16" deep socket and a short extension and remove the three bolts that hold the motor into the regulator, then gently push back on ,motor, remove harness to motor and remove motor through access hole.

Posted on Aug 10, 2009

  • 14092 Answers

SOURCE: How do I change AC blower motor on 1997 Lexus ES300?

THE BLOWER UNIT IS LOCATED IN PASSENGER COMPARTMENT ABOVE THE RIGHT FRONT FOOT WELL.YOU HAVE TO REMOVE THE GLOVE COMPARTMENT LINER.THE GLOVE COMPARTMENT DOOR AND THE AND THE RIGHT LOWER DASH PANEL.THEN YOU CAN REMOVE BLOWER MOTOR SCREWS AND BLOWER MOTOR.

Posted on Aug 11, 2009

Testimonial: "good instructions!"

  • 1986 Answers

SOURCE: Removal of door panel/trim

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 548 Answers

SOURCE: remove antenna motor on Lexus sc430

the antenna is located behinnd the soft panels in the trunk and it is a pretty strightforward operation that consists of removing the retaining screws and disconnecting the wire harness plug . remove the antenna and the rescrew the new one in and replug, voila , you will see it isnt veryhard at all

Posted on Aug 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locaation of the hydraulic roof reservoir on a audi a4 cabrio


BEHIND THE INNER COVER AT THE RIGHT OF THE TRUNK.U MUST TAKE OUT THE COVER..

1 - Flap for convertible roof compartment hinweis.gif Note
t The variable convertible roof compartment must be in the bottom position. t To remove flap for convertible roof compartment -1-, hinges -2- do not have to be removed. t Arrow points in direction of travel. q Bend flap for convertible roof compartment -1- on one side at hinge and disengage flap for convertible roof compartment -1- at hinges. q Fold down flap for convertible roof compartment -1-. q Disengage flap at hooks -4- (2x) by sliding it towards front. 2 - Hinge (2x) q Bend flap for convertible roof compartment -1- on one side at hinge and disengage flap for convertible roof compartment -1- at hinges. q Unscrew bolt -3-. q Disengage hinge -2- from body. 3 - Bolt (2x) 4 - Hook 5 - Variable convertible roof compartment

25573084-tnzdbwhiaswbtdy3r1p2vgzs-2-0.png THEN REMOVE THESE..

1 - Side trim (right-side) t Removing - Take out floor covering in luggage compartment. - Remove rear cross panel trim ? Chapter. - Remove trim for handle mounting ? Chapter. - Remove flap for convertible roof compartment ? Chapter. - Remove luggage compartment light ? Chapter. - Unfasten clip -2-. - Pull off side trim (right-side) -1- in direction of arrow. t Installing hinweis.gif Note
t Following installation, make sure seal is properly in position over trim. - Install trim in reverse order of removal. 2 - Clip

25573084-tnzdbwhiaswbtdy3r1p2vgzs-2-5.png UNDER THIS TRIM U WILL FIND THE MOTOR WITH THE TANK.USE HYDRAULIC OIL THAT U PUT AT THE STEERING RESERVOIR......BEWARE THE SAE OF THE OIL!!!!!
GOOD LUCK

Mar 15, 2015 | Audi A4 Cars & Trucks

2 Answers

2005 lincoln Ls left rear brake light bulb needs replaced. took 2 screws off but metal enclosure is tight and siliconed on. what do i do?


Lamp Assembly -Stoplamp Removal and Installation
  1. Remove the luggage compartment scuff plate.
    • Pull to unsnap.
  1. Position the luggage compartment side trim panel aside.
    1. Remove the pin-type retainers.
    1. Position the luggage compartment side trim panel aside.
  1. Remove the stoplamp assembly.
    1. Disconnect the electrical connector.
    1. Remove the three nuts.
    1. Push the rubber grommet through the sheet metal and remove the stoplamp assembly.
    • If necessary, install new bulbs.

Nov 15, 2010 | 2005 Lincoln LS

1 Answer

The location of the brake light sensor on a lexus rx300 1999 yr the brake lights will not come on when brake is pressed i changed the bulbs the brake switch and fuses so the brake light sensor is the...


it's in the driver side of the luggage compartment, behind the panel that has the power outlet. You would need to remove the trim panel and follow the harness to get to it. Most of the time it's Gray color.

Sep 28, 2010 | 1999 Lexus RX 300

1 Answer

How do I replace my antenna mass on my lexus sc430?


remove the chrome collar on the top VERY carefully with a flat head screwdriver, then go inside the car and turn the radio on. make sure you have someone there to catch it! something else important to know is if all of the antenna doesn't come out, as in there are some broken pieces left inside, you'll have to remove the motor, disassemble it, clean it out, and reinstall it.

Feb 01, 2010 | 2002 Lexus SC 430

1 Answer

How do you remove the broken plastic gear fromthe antenna motor 1997 lexus SC400


You will need to take the antenna motor out and take the cover apart to remove that piece. Pretty simple.

Nov 23, 2009 | 1997 Lexus Sc 400

1 Answer

How do I install the power antenna? I have a replacement, and the wiring is there, but I don't see how to mount the part.


PLEASE DON'T FORGET TO RATE!!!!

Removal & Installation
  1. Lower the antenna and remove the luggage compartment trim panel.
  2. Disconnect the lead-in cable from the antenna and ground strap.
  3. Disconnect the antenna motor wires at the connectors and disconnect the control box connectors.
  4. Remove the top mounting nut and stanchion assembly.
  5. Remove the two nuts retaining the antenna bracket assembly to the quarter panel.
  6. Remove the antenna assembly from the vehicle.
8617042.gif
Some antennas require a special socket to remove the locknut

6210b68.gif
Once its loose the nut can be removed by hand. Sometimes it can be twisted off with a needle nose pliers, but that usually ruins the tool

afa5165.gif
The antenna mounts in the luggage compartment against the support member

abce961.gif
The motor and housing sit on a stand that is bolted to the support member

0ee099b.gif
Unplug the antenna lead from the staff tube

9b0f741.gif
Unplug the connector to the motor

fb68086.gif
Unplug the connector to the relay

d275fd1.gif
Its easier to remove the antennae from the support to gain access to the ground strap screws

To install:
NOTE Correct sequencing for installation is important to prevent water leakage or dimpling of the quarter panel

  1. Connect the antenna cable, power connector and control box connector.
  2. Insert the antenna mast through the quarter panel hole and position bracket on mounting studs in the luggage compartment.
  3. Install the stanchion assembly.
  4. Loosely install the two bracket retaining nuts.
  5. Install the top-mounting nut.
  6. Tighten the bracket retaining nuts.
  7. Install the ground strap.

Nov 19, 2009 | 1990 Lincoln Continental

1 Answer

Porsche Boxter rear luggage compartment lid pull-button problem


remove the two plastic bungs in the side of the cover panel down side of seat, then inside are two 6mm allen screws, these need to be loosened, not removed to allow the trim to be lifted up to access switches. refitting is reversed

Jul 06, 2009 | 1997 Porsche Boxster

1 Answer

How to install power antenna motor on 2001 lexus


The power antenna is a plug and go item. You will need to open the inspection cover on the inside cargo area quarter panel to reveal the motor drive. There you will find a detachable power plug , antenna cord and a series of mounting bolts.
On the outside you will find a chrome bezel which is threaded and may have several notches in it. Using a set of needle nose pliers you can unscrew the bezel which works as a threaded cap and trim ring.
Then remove the internal mounting bolts and the unit should slide down and out from the inside of the cargo area. Take your time and don`t slip forcing the pliers or you will scratch the paint. Nice vehicle, mine is at 160,000 miles and counting

May 18, 2009 | 1999 Lexus RX 300

1 Answer

How to change tail light bulb in 2003 lincoln ls


I can provide 2002, don't have 2003. may be similar. please rate as solveed problem if this is what you needed.

SECTION 417-01: Exterior Lighting 2002 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Lamp Assembly —Rear Removal and Installation
  1. Remove the luggage compartment door trim panel.
    1. Remove the 13 pin-type retainers.
    1. Remove the luggage compartment door trim panel.
93ced34.gif
  1. Remove the rear lamp assembly.
    1. Disconnect the electrical connectors.
    1. Remove the nuts.
    1. Remove the rear lamp assembly.
    • If necessary, install new bulbs.
5f6d88b.gif
  1. To install, reverse the removal procedure.

Mar 22, 2009 | 2003 Lincoln LS

1 Answer

How do I replace a taillight lens on a 1991 Geo Storm?


Rear Turn Signal, Brake and Parking Lights


STORM COUPE
  1. Disconnect the negative battery cable.
  2. Lift the luggage compartment floor carpet toward the front of the vehicle and remove the spare tire cover panel.
  3. Remove the ten plastic retaining clips from the rear end trim panel.
  4. Disconnect the luggage compartment lamp electrical connector.
  5. Remove the luggage compartment trim panel and the rear end trim panel.
  6. Disconnect the rear combination lamp assembly electrical connector. Fig. 1: Rear Turn Signal, Brake and Parking Lights — Storm
84256028.gif
  1. Remove the seven nuts and the rear combination lamp assembly from the vehicle.
  2. Disconnect the rear combination lamp electrical connector.
  3. Remove the four bulb sockets from the rear combination lamp assembly and remove the four bulbs from the sockets. To install:
  4. Install the four bulbs to the sockets and install the four bulb sockets to the rear combination lamp assembly.
  5. Connect the rear combination lamp electrical connector.
  6. Install the rear combination lamp assembly to the vehicle and the seven nuts.
  7. Connect the rear combination lamp assembly electrical connector.
  8. Install the rear end trim panel and the luggage compartment trim panel.
  9. Connect the luggage compartment lamp electrical connector.
  10. Install the ten plastic retaining clips to the rear end trim panel.
  11. Install the spare tire cover panel and the luggage compartment floor carpet.
  12. Connect the negative battery cable.

Mar 21, 2009 | 1991 Geo Storm

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...