Question about GMC Cars & Trucks

Open Question

2010 gmc truck changed the fuel pump rpm & fuel gauge flex back & forth what's the problem?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 958 Answers

SOURCE: fuel gauge moves back and forth from full to empty

you have a bad sending unit inside your tank.
the resistance of the potentiometer inside is broke on the half tank part.

you have to replace it.

tnx 4 using fixya.

drcool

Posted on Oct 05, 2008

Ad
  • 1 Answer

SOURCE: 94 GMC truck diesel starts,runs and then dies and will not start

I have the same problem and have trouble codes 35 and 36. I found out that there is a computer module that needs replaced as it sits low in a valley and gets hot and seperates. I am reseaching about the a/m fix that installs the new module away from heat.

Posted on Mar 12, 2009

csmock132
  • 4669 Answers

SOURCE: 1987 GMC sierra , no fuel pump power.

The inline fuel pump fuse on the passenger side firewall is good? Are you jumping it with 12 volts at the test lead or the fuse?

Posted on Jun 26, 2009

  • 1 Answer

SOURCE: speedometer, gas gauge, odometer, rpm gauge not working

My gas guage, speed odometer and tempiture does not work
The speed odometre is reading 9999999 what should i do

Posted on Oct 21, 2009

GodBlessU
  • 3513 Answers

SOURCE: 2008 gmc sierra 1500 crewcab.

Hi,


A vehicle may be brought into the dealer for a reduced power message, and DTCs P0120, P0220, P1516, P2101, or P2135.

The Throttle Actuator Control (TAC) / throttle body type trouble codes may be caused by a loose wiring crimp at the throttle body connector, or a broken throttle body circuit.

Complete the current SI diagnostics for any symptoms or trouble codes found. If a intermittent T/P or TAC module type code is occurring complete the inspections below.

Inspect all related throttle body terminals for a loose wiring crimp. The loose crimp may be difficult to find, and the poor connection will be between the terminal and the copper strands of the wire. Wiggle test the individual throttle body circuits to see if the concern can be duplicated.
Inspect the related circuits for broken wires inside the insulation. The outer wire insulation may look fine, but the internal copper strands may be partially broken. Breaks in the wires usually occur within 1 to 4 inches of the throttle body connector. Wiggle testing may also induce a trouble code to set.
On C/K trucks complete SI procedures for voltage drop on grounds G103 and G104. Grounds G103 or G104 may be loose or corroded.
If a terminal crimp or a broken wire has been found, repair or replace only the circuits involved. There is a throttle body pigtail connector available through GMSPO, but installing this pigtail connector may cause other intermittent TAC module/TP codes at a later date. If this pigtail must be used, please follow the SI procedures for Splicing Copper Wire Using Splice Sleeves. (the proper Kent-Moore crimping tool must be used for this repair)

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.


Please get back to us if you have any further query or else accept the solution.


Thanks for contacting fixya.com

Posted on Oct 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Ford escape hybrid having wrench dash light.Gas mpg has dropped. Seems to take high rpm for power at times Has been very hot temps outside. If I shut car off and back on, dash light disappears.


Try changing the inline fuel filter if you have not done so in a long time. Check fuel pump pressure, there should be a place under the hood on gas line where you can attach a proper gauge. If you do not have one, most autoparts sellers loan tools, or check it for free. The pump may be bad or the strainer on pump plugged.

Jul 29, 2017 | Ford Cars & Trucks

1 Answer

On a 2000 GMC Jimmy, what causes the fuel gauge to fluctuate?


There is a module in the instrument panel that goes bad. When it does the gauge will move back and forth because the fuel is sloshing in the tank.

Sep 17, 2016 | 2000 GMC Jimmy

1 Answer

1993 GMC Jimmy won't throttle up..changed fuel pump...sounds like fuel is running back into tank


Check fuel pressure regulator.Start engine hook fuel gauge to fuel line check pressure ready then pull the vacuum hose of the fuel regulator if pressure rises 5-10 psi then its good.

May 13, 2011 | 1993 GMC Jimmy

1 Answer

The oil pressure gauge goes from 0 to all the way up and the needle moves back and forth while driving it checked oil its good now its clicking underneath the car and it felt like the transmission was...


First we would need to know when this occurs. Asuming the oil level is at the full mark!. If the pressure goes up during acceleration and down at idle when engine is fully warmed up, then this is normal. An engine requires 10 psi of oil pressure per 1,000 rpm ( ex. 20 psi at 2,000 rpm, 25 psi at 2,500 rpm, and so on ) . If the gauge is moving back and forth erratically at idle , i would say the gauge is bad. If it drops to 0 while accelerating I would say your oil pump is bad. If from time to time it seems to work and other times it seems not to work, I would say the oil pressure sending unit for the gauge is bad. If the pump failed you would start to here a Knocking noise from the engine in a short period of time. Use the above scenario's to narrow down what it may be.

Mar 27, 2010 | 2005 Nissan Altima

1 Answer

Gas gauge dont work jumps back and forth is there a ground?


if it jumps really fast you probably have a bad gauge/instrument cluster. if it moves back and forth with a slower/normal rate of movement you probably have a bad fuel level sending unit located in the tank.

Mar 23, 2010 | 2000 GMC Jimmy

1 Answer

2006 envoy gas cap won't tighten and the fuel gauge reads empty on fill up and fluctuates back and forth.


You can just replace the gas cap...However about the fuel guage fluctuates back and forth...thats due to the sending unit, which is located on the fuel pump itself

Jan 19, 2010 | 2006 GMC Envoy

2 Answers

2006 Yukon Denali, oil pressure gauge malfunction


Most likely the oil pressure sensor is bad. Its located in the very rear of engine on top of bell housing area.

Oct 30, 2009 | 2006 GMC Yukon Denali

1 Answer

I was towing and the hud said hot transmission fluid bring engine to idle. I pulled over and let the tranny cool but since then the trucks shift pattern has changed. First revs to 5000 rpm before changing...


your transmission oil is likely burnt,there by losing it's viscosity. check for brown rather than red fluid on dipstick.have transmission oil & filter changed.it is possible overheating will have caused additional damage.

Sep 28, 2009 | 1999 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...