2009 chevy traverse 3.6 torque specs cylinder head bolts

Nov. 1, 2009 - If you need the head bolt specs, etc, look on this page: ... Cylinder head torque in the '95 states 3 passes building up to 65 ftlbs. Don't have the ...
Head bolt torque
Feb. 23, 2002
Torque Specs
Nov. 3, 2019
Head Bolt Helllppppp!
Apr. 3, 2010
Head Torque Specs
Nov. 3, 2019
More results from www.impalassforum.com

Apr 10, 2021 • Cars & Trucks

0helpful

1answer

I have a 1995 chevy beretta with a 2.2liter. What is the torque spec for the head bolts?

Here's a link to your head bolt torque. Repair Guides Engine Mechanical Components Cylinder Head AutoZone com

Mar 22, 2015 • 1995 Chevrolet Beretta

1helpful

2answers

TorqueTo What Foot Pound On Cylinder Hesd Bolts For Chevy Monte Carlo 2002 3.4 Engine

You can usually do a Google search for this type of information.

Here ya go.
Cylinder Head Bolt Torque Specification GM 3 1L and 3 4L Engines

Feb 22, 2015 • Cars & Trucks

0helpful

1answer

Need head bolt torque specs for a 1996 saturn sl

Quote:

Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 • 1996 Saturn SL

0helpful

1answer

Cylinder head bolt specs and secquence on chevy caliver 1996 2.2 l

Torque sequence ------------ front ' 8 4 1 5 9 ' of ' ' engine ' 7 3 2 6 10 ' ------------ Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs Step 2: torque all bolts an additional 90 degreesRecheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Hope it helps you.

Jul 30, 2011 • Chevrolet Cavalier Cars & Trucks

2helpful

1answer

Need the cylinder head torque specs for a 5.7 TBI 88 chevy 2500 pu

cylinder head torque spec is
step 1, 25 ft-lb
step 2, 45 ft-lb
step 3, 65 ft-lb

bolt tightening pattern
front of vehicle is on left just for referance.
13 5 2 10
17 9 1 6 14

16 12 8 4 3 7 11 15
i hope that makes sense and helps.

Mar 21, 2010 • 1994 Chevrolet C1500

1helpful

1answer

Torque specs

Head bolt torque is 65 ft lbs, use the below sequence, go over bolts 3x to reach final torque (not all at once to 65)

13 5 2 10
front of engine 17 9 1 6 14
16 12 8 4 3 7 11 15
good luck!

Oct 25, 2008 • 1988 Chevrolet K1500

Question 2

Kardoc

Cars & Trucks Master 7,503 Answers
Posted on Apr 18, 2019

Kardoc

Cars & Trucks Master

Joined: Sep 18, 2010

Answers

7503

Questions

0

Helped

2756783

Points

58323

Http://www.championbrands.com/aera-torquespecs.pdf Check this torque chart for your head torque.

youtube.com

How To Bleed Hydraulic Clutch Wrenchin Up

Answer 2 · 9/8/2008 12:00:00 AM

Marvin

85242 Answers
Posted on Sep 08, 2008

SOURCE: 2005 Tucson

camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.

Anonymous

783 Answers
Posted on Mar 19, 2009

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

20 Nm (15 lb-ft).

40 Nm (30 lb-ft).

50 Nm (37 lb-ft)

Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:

Tighten to 40-50 Nm (30-37 lb-ft).
Rotate an additional 175-185 degrees.
Go to next bolt in sequence.

Short Bolts:

Tighten to 20-30 Nm (15-22 lb-ft).
Rotate an additional 175-185 degrees.
Go to next bolt in sequence.

Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Anonymous

462 Answers
Posted on Jul 04, 2009

SOURCE: what torque spec for chev aveo 2004 cylinder head

18 lb ft+60°+60°+60°+10°

NEW HEAD BOLTS ARE REQUIRED WHEN REPLACING THE HEAD OR HEAD GASKET.

Anonymous

1392 Answers
Posted on Aug 16, 2009

SOURCE: head bolt torque spec

Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

Anonymous

233 Answers
Posted on Sep 17, 2009

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below

Answer 3 · 9/8/2008 12:00:00 AM

Marvin

85242 Answers
Posted on Sep 08, 2008

SOURCE: 2005 Tucson

camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.

Answer 4 · 3/19/2009 12:00:00 AM

Anonymous

783 Answers
Posted on Mar 19, 2009

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

20 Nm (15 lb-ft).

40 Nm (30 lb-ft).

50 Nm (37 lb-ft)

Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:

Tighten to 40-50 Nm (30-37 lb-ft).
Rotate an additional 175-185 degrees.
Go to next bolt in sequence.

Short Bolts:

Tighten to 20-30 Nm (15-22 lb-ft).
Rotate an additional 175-185 degrees.
Go to next bolt in sequence.

Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Answer 5 · 7/4/2009 12:00:00 AM

Anonymous

462 Answers
Posted on Jul 04, 2009

SOURCE: what torque spec for chev aveo 2004 cylinder head

18 lb ft+60°+60°+60°+10°

NEW HEAD BOLTS ARE REQUIRED WHEN REPLACING THE HEAD OR HEAD GASKET.

Answer 6 · 8/16/2009 12:00:00 AM

Anonymous

1392 Answers
Posted on Aug 16, 2009

SOURCE: head bolt torque spec

Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

Answer 7 · 9/17/2009 12:00:00 AM

Anonymous

233 Answers
Posted on Sep 17, 2009

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below

Related Topics:

Trustworthy Expert Solutions

2009 chevy traverse 3.6 torque specs cylinder head bolts

1 Answer

Kardoc

5 Related Answers

Marvin

Anonymous

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

2003 Mitsubishi Lancer with 4G18 engine. I need cylinder head torque specs please?

Head bolt torque specs and pattern

2006 Dodge Caravan 2.4 main bearing torque specs please.

What are the torque specs for the rod bearings on a 2006 - Fixya

Dodge Caravan 2.4 need engine tightening specs and head ...

Torque Specifcations - MAHLE Aftermarket

Torque specs for a 2006 Chevy Cobalt please?

2006 Chevy cobalt 2.2 L engine torque specs for - Fixya

Torque Specs!! - Cobalt SS Network

Torque Specs, Fluid Capacities ' Chevy Cobalt Forum

Chevrolet Lug Nut Torque Specs Table - Sparky Express

What is the torque on 2004 chevy impala head bolt

list of trq specs ' Chevy Impala SS Forum

I have a 1995 chevy beretta with a 2.2liter. What is the torque spec for the head bolts?

TorqueTo What Foot Pound On Cylinder Hesd Bolts For Chevy Monte Carlo 2002 3.4 Engine

Need head bolt torque specs for a 1996 saturn sl

Cylinder head bolt specs and secquence on chevy caliver 1996 2.2 l

Need the cylinder head torque specs for a 5.7 TBI 88 chevy 2500 pu

Torque specs

Not finding what you are looking for?

Cars & Trucks

2003 Mitsubishi Lancer with 4G18 engine. I need cylinder head torque specs please?

Ask a Question

Popular Questions

Toyota dashboard CD player won't eject

4.3 Firing order diagram for 4.3L v6 Chevy engine

BMW X5 Trans Fail Safe Program,

Diagram of 1996 ford ranger fusebox which fuse is

What does my check engine light trouble code $7e8 mean?

Check Out the Latest Top Trucks Report!

Top Cars & Trucks Experts

ZJ Limited

john h

Arnie Burke

Are you a Car and Truck Expert? Answer questions, earn points and help others

Manuals & User Guides

DIS9_Full.pdf. user-manual-1994...

DIS9_Full.pdf. user-manual-1994...

Rhonda_Docs.pdf. user-manual-2001...