Cars & Trucks Logo

Related Topics:

g
glen cooke Posted on Apr 12, 2019
Answered

Where is the heater blower resistor and what does it look like?

Answer This Question

1 Answer

Julie

Julie

Level 1:

An expert who has achieved level 1.
Corporal:

An expert that has over 10 points.
Welcome Back:

Visited the website for 2 consecutive days.
Problem Solver:

An expert who has answered 5 questions.

  • Contributor 6 Answers
  • Posted on Apr 10, 2022
Julie
Contributor
Level 1:

An expert who has achieved level 1.
Corporal:

An expert that has over 10 points.
Welcome Back:

Visited the website for 2 consecutive days.
Problem Solver:

An expert who has answered 5 questions.

Joined: Apr 10, 2022
Answers
6
Questions
1
Helped
913
Points
12

By the blower motor, looks like a computer card with a connector on it.

5 Related Answers

Anonymous

  • 2 Answers
  • Posted on Dec 25, 2008

SOURCE: air conditioner blower motor resister on dodge grand caravan

in my 2004 grand caravan it's behind the glove box and left of the blower motor. disconnect the wires first then remove the 2 screws to pull out the resistor unit. First make sure you have removed the negative of your batterie. I had the same pm that prevented the blower motor to operate in any speed. I hope this will help

Ad

Anonymous

  • 1 Answer
  • Posted on Feb 01, 2009

SOURCE: locating heater blower motor resistor

the resistor is behind your glove box. open the box and push in the sides to release it and let it hang down...the resistor is right there. I didn't try to replace it, a friend did it, but the part was under $20.

Anonymous

  • 236 Answers
  • Posted on Feb 22, 2010

SOURCE: Brake Fluid for 2008 Avenger

it's DOT 4 or DOT 5 check with your manual and sometimes it's even in the fluid fill cap.

Testimonial: "Quick response, guided me in the right direction. Thanks!"

Anonymous

  • 1 Answer
  • Posted on Feb 23, 2010

SOURCE: 2008 dodge avenger spark plug location and socket size.

  • 2008+ Dodge Avenger 2.4L 4cyl.
  • Remove plastic cover on top of engine, just pull on each corner for it is friction fit.
  • Once removed you will see 4 black spark plug covers with one hex type screw holding each.
  • Remove Hex screw and place aside, pull upward to remove plug boot from plug.
  • To remove the plug, use a 5/8 socket with a 6" extension. Once plug has been turned out all the way and you cannot get the plug up and out of the hole, just press the plug boot back on the plug and pull it back up.
  • Gap and replace 4 plugs with the same or equavalent type,. Drop plug down the hole and use socket to align and tighten until just snug, then torque to manufactures specifications.

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Nov 16, 2010

SOURCE: where is the battery located

To access the battery, turn the wheel fully to the right and remove the left front inner fender shield. The information is on page 379 of the owners manual

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
2answers

Where is the heater resistor on a 2005 dodge dakota? Behind glove box?
should be just above the blower motor. You will need to remove the glove box door to gain access.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Read full answer
Dec 12, 2015 • 2005 Dodge Dakota Club
1helpful
1answer

Remove heater control switch
Before removing the heater switch on this 2006 citroen hdi I would first have the blower motor checked and the most common reason for this and other blower problems would be the blower resistor.

Your blower works on and off at times, first locate the blower motor and the resistor. the blower motor is located on the heater box, look under the pass/side of the dash, you may have to remove under dash cover to see blower.
When you have located the blower now look to the side on the heater box, there you will see a connector plug, it plugs into a connection on the heater box, this will be the resistor, the resistor slides into heater box and the end of it bolts to box to hold it in place and then the connector plugs into it, if you can not locate it then follow wires that plug into blower , follow wires back they will lead you to resistor,
next time blower does not work wiggle connector to resistor and see if blower turns on, if it does then resistor is the problem. also unplug resistor plug at resistor and check for any burning of connectors at plug and inside resistor.

I would bet its a bad resistor or the plug is brunt due to high draw from bad connections, if plug has burn damage to connectors then replace the plug along with resistor.
Read full answer
Jul 08, 2012 • 2006 Citroen C5 HDi
2helpful
1answer

How to change blower motor in. 99 grand Cherokee
Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

zjlimited_1958.jpg


Hope this helps (rerember to rating this and leave a testiomonial).
Read full answer
Sep 30, 2011 • 1999 Jeep Grand Cherokee
2helpful
1answer

The heater fan on my 1993 f-350 has become really loud. I only have hi speed which I understand may be a resistor issue but how do I remove the fan and motor assembly to inspect it?
A heater blower motor resistor is an electronic device with three or more progressive resistors that allow the heater blower motor to operate at slower speeds. The highest speed of the heater blower motor is not controlled by the resistor, so when the resistor fails, the fan will often work on the highest speed setting, but not the lower speeds.
To resistor is generally located under the dashboard and under the hood, near the blower motor . The resistor's electrical connector is disconnected, the resistor is removed and the new resistor is installed. On some vehicles it may be easily accessible, and on others it may take partial dashboard removal to replace the resistor.
Look under the hood, generally the wiring for the Blower resistor is attached to the wiring to the blower motor itself
It's inboard & below the motor, near the accumulator. You can see it standing beside the passenger fender. it's the off-white connector behind the L heater hose above the vacuum reservoir & the white WARNING sticker
Read full answer
Feb 12, 2011 • 1993 Ford F350
1helpful
1answer

How do i change blower motor resistor on 99 jeep grand cherokee

Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Read full answer
Nov 22, 2010 • 1999 Jeep Grand Cherokee
1helpful
3answers

Blower motor resistor, where is it located/
It will be up under the dash on the passenger side near the blower motor. It will have 5 or six wires in its connector

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Read full answer
Nov 10, 2010 • 2000 Jeep Grand Cherokee
6helpful
1answer

Fuse diagram for a 98' E-150 van specifically for heater fan
owner manual will tell you fuse layout. If you have only high speed, you have a bad resister. 4 wires.

Resistor —Heater Blower Motor Switch Removal
  1. Remove the battery (10655) ; refer to Section 414-01 .
  1. Remove the battery tray.
    1. Remove the screws.
    1. Remove the battery tray.
  1. Disconnect the heater blower motor switch resistor connector.
  1. Remove the heater blower motor switch resistor (18591).
    1. Remove the two screws.
    1. Remove the heater blower motor switch resistor.
---------------------------------

0f120f5.gif
Read full answer
Feb 26, 2010 • 1998 Ford Econoline
6helpful
2answers

VW Jetta GL 2000, AC - Heater Fan stopped
blower motor or resistor or the blower motor control switch.
Read full answer
Jun 01, 2009 • 1998 Volkswagen Jetta
1helpful
1answer

I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...
it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------
Read full answer
Mar 31, 2009 • 2007 Ford E-350 Super Duty Length XLT
0helpful
1answer

Where is the heater blower resistor located
Blower Motor Resistor
The four-speed operation of the blower motor is achieved through the blower motor resistor. The blower motor resistor is mounted under the A/C evaporator/blower motor assembly.
-----------------------------------------------------------------------------------------------------------------

the heater blower resister is in the heater plenum under the dash on the passenger side. the resister is in the air stream to keep it cooled. it has 2 screws holding it in and a 3 or 4 wire connector on it. easy repair. buy resister from tascaford.com for 25% off.


Read full answer
Dec 06, 2008 • 1999 Mercury Villager
Not finding what you are looking for?

View Most Popular

2008 Avenger

  • Cars & Trucks

Related Question

Where is the heater resistor on a 2005 dodge dakota? Behind glove box?

  • 2005 Dodge Dakota Club

163 views

Ask a Question

Usually answered in minutes!

Popular Questions

2.4 Dodge avenger belt Diagram

2011 Dodge Avenger

How I take the battery off my car?2008 Dodge

2008 Dodge Avenger

2008 dodge avenger spark plug location and socket size.

2008 Dodge Avenger

Where is the battery located

2008 Dodge Avenger

Where is the inside fuse box on 08 dodge avenger located

2008 Dodge Avenger

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. 2008 Avenger Manual

2008 Avenger

Loading...