P 3335 dtc fault code for ford - Ford Cars & Trucks

B2296 d 44 Restraint System - Impact Sensor Fault (Driver Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test V .
Pinpoint Test V: LFC 42, 43, 44, 45, 46 and 47/DTC B2296 - Restraint System - Impact Sensor Fault
Normal Operation
The restraints control module (RCM) checks all of the impact sensor circuits for faults. If the RCM detects one of the following faults on any of the impact sensor circuits, it will store diagnostic trouble code (DTC) B2296 in memory and flash, depending on the fault, either lamp fault code (LFC) 42, 43, 44, 45, 46 or 47 (or higher priority code if one exists) on the air bag indicator.
Fault Conditions
The RCM monitors for the following fault conditions:

• Low resistance
• Circuit open
• Circuit short to voltage
• Circuit short to ground
• Internal faults
• Communication faults

Possible Causes
A impact sensor status fault can be caused by:

• damaged wiring, terminals or connectors.
• a faulty impact sensor.
• incorrect sensor mounting.
• RCM is faulted.
• There are 72 steps involved in the diagnostic testing procedure for this DTC. Your best bet mite be to just replace the sensor an see if that fixes the problem, if not ?

How to solve Gs 01 actros fault code

It is a common misconception that the instrument cluster self test gives DTC's for the engine management system, it provides cluster related DTC's on test 10 of the cluster self test, DTC should be displayed above the code, these will be displayed at 1 second intervals, once you press OK again the cluster will scroll to the next test, the format of the codes shown in the cluster is designed for Ford engineering and can only be translated into usable codes by Ford IDS.

The only way to find out why the engine management light is on is to have a scan of the engine management control module carried out using an appropriate code reader, this will give you the standard EOBD codes for example a catalyst efficiency code would show P0420. If you want to do this on a DIY basis then cheap code readers are available on the internet for around $75.00, these code readers also reset the light after the fault has been fixed. if this was helpful please leave me good feedback

Did you ever get to the bottom of this? I am having exactly the same issue with my 2006 Focus 1.6 tdci

Continuous Memory Diagnostic Test Code (DTC) P1270 has a generic description of "Excessive Engine RPM/Vehicle Speed".
This DTC indicates that the vehicle was operated in a manner which caused engine or vehicle speed to exceed a calibrated limit. Possible causes for this DTC are:
> Wheel slippage caused by mud, snow, water, ice. etc.
> Excessive engine RPM in Park or Neutral
> Vehicle driven at an excessive rate of speed

If you are aware that one of the possible causes above occured, then there is no problem.
If there are no other drivability symptoms or fault codes, simply clear the code and move on.

All fault codes can be checked out at http://www.bluejag.co.uk but here are the results for some of yours. You can ignor P1111. Looks like a faulty plug or coil pack cylinder 2

Fault Code:- P1314 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire rate catalyst damage -bank 2 NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- ECM Default:- Maximum engine speed reduced


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure
Fault Code:- P1316 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire excess emission NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure

Fault Code:-
P0302 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire detected ?€" cylinder 2

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Refer to P0300 Possible Causes

The code U1262 point out a communication fault between the vehicle modules and a scanner. It may be best to visit your local dealer to find if one of the vehicles control modules has failed. In some cases this can be as simple as a blown fuse, but there is always a reason for a fuse to blow
and a oil sending circuit fail. would need to be tested.
P1000 DTC code is a manufacturer specific trouble code. your code reader is not reading or communicating correctly you will need to check the fuses for all the modules and check the connections on the plugs and the units to check the modules to see if they have good contact. also check the main earth from the battery to the shell and make sure the contact is good.