Removing the plastic cover on bissell power lifter I removed the screws but cannot get the cover to pop off

for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

Almost all door panels are attached by:
SMALL PHILLIPS HEAD SCREWS- these are found all around the door panel. They are normally hidden by; small plastic grommets (round, flat plastic push tabs used to cover and make it look pretty!)
-remove with flat head screwdriver or your nails at-own risk,
THE SPEAKER COVER-
-easily popped off by squeezing outer edges inwards releasing the male part on the speaker cover from the slot on the door panel
and
THE RUBBER OR PLASTIC COVER- found on the inner side of the door handle
-this cover may not be there for your model and you may see the screw or the grommet. If not, remove cover with flat head screw driver or needle nose plyers, then remove screw/s


Tips:
1)check for grommets if screw/s are not in plain sight)- plastic push tabs (flat head and round about a 1/4 to a 1/2 inch in diameter, normally matches the car door panel and fits flush with the panel as well so look closely! You will need a flat head screw driver for this part or try your nails at own risk.),

2) Once you have removed all the screws and or push tabs shake the panel to pin point any remaining screws or tabs. Some times there are slots in the door frame that join with the male part located on the inner side (touches the door) of the plastic panel.

good luck!

Purchase replacement part first.
If you need motor only it might come without regulator.
Either way when you have the new part(s)
It will give you an idea of what has to be removed
look for plastic covers (round) or screws and remove them under the covers are screws also remove those.
neer door handle there is always a screw or tab.
on the pull handle (big one) there are 1-2 large screws remove those.
look near mirror area and remove any plastic covers. may be tabbed or screwed in??
usually lifting lightly and looking under the trim with a flashlight will tell you what is holding it.
remove plastic from around handle area.
pry lightly on the bottom and see if you have to lift up or straight out.
either way usually an up and out motion is required at same time.
tabs lift out easily while the push in plastic tabs may be more strong. if they stay in the door remove them later with trim tool. looks like a dandelion puller. then put them back on the door trim whre they came from for later installation.
If door has plastic film pull it away from the door and don't get the black stuff on you. Sticky!
Then find if regulator is bolted in or pop riveted in.
remove bolts or pop rivets and dont pinch your fingers but separate window glass from regulator.
This is the fun part you will have to find a hole to pull it out of. usually there is only one choice. and that is the biggest hole there.

take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.

1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
   
2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
   
3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
   
4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
   
5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.
   
6. 
   Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.
   

If you have power windows and door locks, take a small flat-tip screw driver, and gently pry up the switches. Unplug them. If not power, The auto parts store have a window handle removal tool. Remove the handle. Then unscrew the door lock at the top right corner of the door. Unscrew the door handle. Screws are located under the handle. If you have the pull strap, remove the covers with a screw driver. covers are at both ends of the strap. The auto parts store also sells a door panel removal tool. put that between metal and plastic cover a gently pry. it will pop the clips loose. Take your time and be gentle. after popped loose. gently tap up from the bottom. this will get it to release the clip from the frame by the window. Hope this helps.

hi,
most screws are visible to you, there are two screws hidden in the grab handle(which will just lever off, away from the door)
when all screws (along the bottom and the top closest to the A pillar) are removed the plastic must be pulled away from the door, as it is now held on with push clips. once removed , the window lifter mechanism will have to be removed, but by the sounds of it , I'd say the lifter is what's broken. it is a fairly common fault
Regards
P

It's easy!

1. Remove triangle-shaped plastic cover Fwd of door window - gently pry it off
   
   
2. Remove screw from the plastic cover behind door open lever
   
   
3. Remove door lock plunger. (unscrew)
   
   
4. Remove screws down inside the door pull hand-hold area
   
   
5. Look for other phillips screws - sometimes around the lower 1/2
   
   
6. Pry hidden plastic hold down fasteners from around the edge - pull the panel away from the door and where you see it 'stuck' to the door, slide a pry tool, a stiff putty knife works well, up in that area and pop the fastener off.
   
   
7. Lift door liner enough to get to the mirror power connector and unplug.
   
   
8. For some model years, with door panel loose, you can access the bolts / screws that hold the interior trim piece in place and remove.
   
   
9. Remove Mylar cover for access to 3 Mirror mount studs, speaker screws, door lock actuators, window motors, etc.
   
   
10. Remove nuts, (hold the mirror up from outside) and remove mirror. (Feed electrical harness through door openings as required to facilitate removal.
    
    
11. Reverse order for installation.

there should be an access panel in the trunk.

This panel is held in by plastic snaps. After all the screws are ou it pops off not a sliding type. Hopefully your window rolls down it is easier. !st take the plastic cover off of latch mechanism in rear of penal On the seat switch you'll find the top wooden portion pulls off grab from the bottom. then there is a bracket that unscrews and the seat switch wood pops out. next open the armrest and you'll see a plastic cover held in by a small black screw. remove and then remove the big screw behind it, I believe there is also a screw in the front of the map pocket and possibly 2 more in the center. pop out the light at the bottom of the panel and un clip wire harness. Next pop pout the top side view mirror cover. I believe there may be a couple of plastic grommets on grab handle that pop out giving you access to the screws. Next pop off the door panel by grabbing at the bottom and pulling outwards. be carefully because there is a vacuum line attached to the map pocket lid locking mechanism. once panel is loose un clip vac line and electrical and grab handle linkage. you should then be able to remove panel completely. i do not have an sl in front of me so look very carefully for any screws I forgot to mention. This is the best I can do from memory. good luck

You will have to remove the entire door cover. Remove any screws you can see, pop off the cover behind the door handle remove screws behind that, pop off the plastic that holds power window switches and unplug them, then you will have to pull the door panel upwards to remove.