Hit the lock button first then hit and hold the start button the arrows in circles button
It was an option so I would make sure you actually have it.
The only way to know for sure is to check the cars option codes (usually on a label in the glove box and/or trunk) and compare them with a complete list for your car (Google that list). That option should also be described in the user manual with user instructions.
SOURCE: nissan murano 2005 sl keyless entry remote programing
Close all vehicle doors, LOCK doors using drivers side switch.
Insert key all the way into the ignition, (do not turn) remove key.
Repeat this step 5 times. (6 total)
Hazards should flash to indicate program mode.
Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.
*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press
any button on remote, hazards should flash. Repeat step as necessary.
Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.
Source
SOURCE: can't find button under dash to reset/reprogram keyless entry
check this out - its not like the previous link - the button actually floats around with the wiring.
http://www.rs25.com/forums/showthread.php?s=8876327367f08262d9b387a75d9b5919&t=41265&page=2
SOURCE: programming a keyless entry remote
Key Fob Auto Learn
This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.
Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming.
The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.
Good luck and hope this help's keep me posted, there are 3 other methods and the 5th method is a tech 2 scan tool that the dealer uses but this should work on your year of cadillac.
SOURCE: how to program a keyless entry remote for a 2001
Hello, To answer your question about programming a keyless entry remote you need a scanner tool that has the capability to accomplish this task. A GM Tech 2 or something else that has the ability to do what the Tech 2 does. I know this is not what you want to hear but I am reading it right out of the Cadillac Service Manual. Thank you
Testimonial: "Thank you so much for the helpful reply!!"
SOURCE: How do you program a
you have to use a paper clip and bridge #4 and #8 terminals on the OBDII connector (then turn key on), then hold the lock/lulock buttons at the same time-the terminals are the top row, 4th and 8th(end) from the left side of the connector. Horn will beep 3 times when the code is learned by the new remote.
80 views
Usually answered in minutes!
×