The service and repair manual with diagram will give you step by step help to locate and fix the problem on your own easily and you will get the manual from the given link https://toolsnyou.com
SOURCE: location of the fuel pump relay or fuse
fuel pump in the fuel tank note that all ford are equipt with cut of suitch (interuptor) located under dach board in case of colision ,towing, ect.....this electrical devise wil stop the flow of the fuel to prevent car fire
SOURCE: no injection pulse
looking at the schematics, well the PCM controls the pulse width to the injectors , BUT , there is a injector coil fuse , its #2 in your kick panel fuse box , a 20 amp , check it , sure hope that fix ya . that would be sweet .
J5
SOURCE: 1985 corvette no pulse to injectors
Very important that if you are not savvy of working on your Vette ...you would be better off - taking your car to a dealership for repairs on your trouble codes. However if you feel that you want to, First locate your car's alcl this component is located just below the instrument panel and to the left of the center console. Remove the plastic cover the first two slots to your right are the A & B slots.
The A slot is the diagnostic slot and the B slot is the ground slot. Insert the computer key into these slots if you do not have a computer key, a paper clip or wire jumper clip will do, (with the engine off) this is very important...now only put the ignition key to on ( not start !!!) the check engine light will display a code 12 which is one flash followed by two flashes. This code will be flashed three times ..followed by the trouble code stored in your car's computer.
What ever the code is it will be flashed three times. Have a paper and pencil ready and write down the code.
Code #12: Normal No Codes.
Code #13: Open Oxygen Sensor Circuit.
Code #14: Coolant Sensor Circuit Low.
Code #15: Coolant Sensor Circuit High.
Code #21: Throttle Position Sensor High.
Code #22: Throttle Position Sensor Low.
Code #23: Manifold Air Temperature Circuit High.
Code #24: Vehicle Speed Sensor.
Code #25: Manifold Air Temperature Circuit Low.
Code #32: EGR System Failure.
Code #33: Mass Air Flow Sensor High.
Code #34: Mass Air Flow Sensor Low.
Code #36: Mas Air Flow Sensor Burn-Off Function Fault.
Code #41: Cylinder Select Error.
Code #42: Electronic Spark Timing.
Code #43: Electronic Spark Control.
Code #44: Lean Exhaust indication.
Code #45: Rich Exhaust Indication.
Code #46: Vehicle Anti Theft Fault.
Code #51: Faulty Mem-Cal.
Code #52: Fuel Calpak Missing.
Code #52(1990-91 Corvette Only): Engine Oil Temperature Sensor Low.
Code #53: System Over Voltage.
Code #54: Fuel Pump Circuit Low Voltage.
Code #55: Defective ECM.
Code #62: Engine Oil Temperature Sensor Circuit High.
Please remember that if you have the computer key installed in the alcl and you start the engine (you will ruin the engine's computer) only put the ignition to on (not to start).
If you should get a check engine soon display.. you can use the above procedure and codes to buy the right part or at the very least to keep from getting taken for a ride and be made to pay hight prices for some inexpensive module that you could have installed yourself.
If your engine displays a trouble code ... your engine will go into limp mode ..it will still run but very poorly. You might be able to reset the computer if it will not start (just to get home) by disconnecting both battery cables and re-installing them ...this is not recommended ..but if you are stranded it might help unitl you get your car home or to a repair shop..good luck.
Good luck and hope this helps.
SOURCE: no power tp the fuel pump, injectors not pulsing, no fuel.
Check out your oil sending unit, fuel pump and relay, check for power (might be a fuse), the ignition control module (which if you remove it, can be tested for free at AUTO-ZONE), any related wiring, pick-up coil (inside the distributor), and possibly the ignition switch. If I can be any more help just as away.
SOURCE: why does the fuel injector receive no pulse for
The 6 cyclinder motor has 6 fuel injectors. If your not getting pulse Electrical grond to an injector wire theirs a likly chance your not getting it at another. If your getting no pulse at all the engine won't run. Does the check engine light on with the engine running? What meadod did you determine that it had no pulse? Remove one injector wire one at a time with the engine running? If it's not running at all then the no pulse can be a common system part like the crank senser. Does the engine get spark? Most of the time pulse and spark are hand in hand so if the crank senser were bad it's not going to have s[ark either.
485 views
Usually answered in minutes!
×