Where is the tccsolenoid on a 1997 chevy silverado 1500 automatic 4 wheel drive

SOURCE: 2000 chevy 1500 truck stuck in 4-wheel drive

the shifter accuator or the wires going to it on the transfercase..gl

Joe Lamb

• 463 Answers
• Posted on Mar 27, 2009

SOURCE: 2000 silverado z71 service 4 wheel drive light on/off

The problem is with the front actuator.Its flashing in the dash lights because is not functioning properly.Replace actuator and fix problem.Its a 4 or 3 wire screw in plug in front axle,,

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_a3369546f8067589

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Harvey N Tawatao

• 3854 Answers
• Posted on Apr 08, 2009

SOURCE: 4 Wheel Drive Problem

Put the key in the run position and turn your 4wd on and off to listen for the electronic acuator to engage and disengage. If your can hear it then it's macanical and a Quick fix. On top of the transfercase on the driver's side, your going to find three vacuume tube connected to a cauume switch that may have gone bad. There common to go bad and there not the bad of a price at the Auto Zone. Check for any cracks on the vacuume line first then get your hands dirty. Good luck and keep an extra switch in your glove box.

Donnie Matney

• 426 Answers
• Posted on Jul 06, 2009

SOURCE: 1997 z71 Transmission removal

1. Disconnect the battery negative cable.
2. Raise the vehicle. Support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
3. Disconnect the range selector cable from the transmission bracket and from the transmission range select lever. Refer to Shift Cable Replacement .
4. Remove the rear propeller shaft. Refer to Rear Propeller Shaft in Propeller Shaft.
5. Support the transmission with a transmission jack.
6. Remove the transfer case if equipped. Refer to the appropriate Transfer Case Replacement in Transfer Case:
• Transfer Case Replacement (Selectable Four Wheel Drive) . • Transfer Case Replacement (Auto Four Wheel Drive ) . • Transfer Case Replacement (Manual Four Wheel Drive) .



7. Gasoline Engine--Remove the following components:
7.1. Two bolts 7.2. Two washers 7.3. One nut 7.4. The transmission to engine brace



8. Diesel Engine--Remove the following components:
8.1. Two bolts 8.2. Two washers 8.3. One nut 8.4. The transmission to engine brace
9. Remove the transmission rear mount.
10. Remove the frame crossmember.
11. Remove the exhaust pipe from the exhaust manifolds. Remove the muffler assembly from the exhaust pipe, if required. Refer to Exhaust System.




12. For the 5.0L Gasoline Engine: Remove the six bolts securing the converter cover to the transmission.
13. Remove the starter. Refer to Starter Replacement in Engine Electrical.
14. For the 4.3L Gasoline Engine: Remove the dust plug at the end of the starter mounting port in order to gain access to the converter bolts.




15. For the Diesel Engine and 7.4L/5.7L Engines: Remove the four bolts securing the converter cover to the transmission.
16. Mark the flywheel and the torque converter alignment.




17. Remove the bolts that attach the torque converter to the engine flywheel.




18. Remove the transmission vent hose.
19. Disconnect the wiring harness connectors from the vehicle speed sensors and from the park neutral position switch.
20. Remove all vehicle electrical harness wires, harness clips, tubes, and brackets that may interfere with the removal of the transmission.
21. Remove the fluid fill tube and the fill tube seal from the transmission. Refer to Filler Tube Replacement .
22. Plug the fluid fill tube opening in the transmission.
23. Disconnect the transmission oil cooler pipes from the transmission. Refer to the oil cooler pipe quick connect fittings removal procedure in Oil Cooler Hose/Pipe Replacement .
24. Plug the transmission oil cooler pipe connectors in the transmission case.
25. Install the J 21366 in order to keep the torque converter from sliding off of the transmission turbine shaft.
26. Support the engine with a suitable jack stand before removing the transmission from the engine.




27. 5.0L and 5.7L Gasoline Engine: Remove the studs and bolts securing the transmission to the engine.




28. 4.3L Gasoline Engine: Remove the studs and bolts securing the transmission to the engine.
29. Pull the transmission straight back from the engine.
30. Lower the transmission using the transmission jack.
31. Flush the transmission oil cooler and the pipes whenever you remove the transmission for overhaul, or replacement of the torque converter, the pump, or the transmission case. Refer to Transmission Fluid Cooler Flushing .
32. Clean the transmission case using a solvent dampened cloth. Do not allow solvent to enter the transmission.
33. Air dry the transmission.
34. Clean all hardware and the flywheel cover using solvent. Air dry all the parts.
35. Inspect all the components for wear and damage.
36. Inspect all the seals and the fittings for signs of wear.
37. Inspect the torque converter for stripped or broken weld nuts.
38. Inspect the transmission case for cracks.

SOURCE: 2004 chevy silverado 1500 4 wheel drive wont work..

try selecting from nutreul or less then 3km