Question about Ford Taurus

1 Answer

How do i connected a jumper wire to the fuel pump relay to make the fuel pump run?

2005 ford taurus. the fuel pump relay have numbers on it and they are #1, #2, #3, #4, #5 but i don't know which number to connected the Jumper wire to. i think the fuel pump relay is number 29 in the fuse box the pump want run when i turn the key on i replace a new fuel pump assembly. i check all the fuses they are good but i don't hear the pump relay click when i turn the key on.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 139 Answers

Replace the relay, jumper wire wont work, there is a small set of points inside the relay, there probably burnt, or stuck open

Posted on Mar 15, 2019

  • 1 more comment 
  • Joe Russell Mar 15, 2019

    i change relays around still pump want run and i don't hear the relay click when turn key on. what i check now?

  • stephen peirce Mar 29, 2019

    That's because the fuel pump driver module in the trunk is bad and needs to be replaced go to rockauto.Com and look up your vehicle then the part so you can see it this is on the inside trunk braces on the side and is responsible for final energizing of the fuel pump

  • Joe Russell Apr 22, 2019

    is there a way i can connect a jumper wire to the fuel pump to make it run? how do i test the drive module with a multimeter?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: 1991 ford explorer fuel pump assembly, fuel pump

Change fuel pump

Posted on Oct 25, 2008

  • 784 Answers

SOURCE: 91 ford ranger...fuel pump will not run pump is good

It won't hurt to jump sire to drive, It is designed to pump all time when the engine is running. The only problem is the pump should not be on if engine is not running since it is designed that way to prevent a fire while pump continues on once engine is stops in a car accident. There is a control device to immobilize the fuel pump, if there is no speed sensor signal from the crankshaft. This needs to be located and fixed.

Posted on Oct 14, 2009

  • 227 Answers

SOURCE: 97 chev express 2500 --

replace relay

Posted on Feb 03, 2011

Geekman
  • 32281 Answers

SOURCE: On my 97 grand prix3.8 I have used a jumper wire

There is a break in the wire that supplies power to the fuse box.
You need to trace this power wire from the fuse box to find the break in this wire and fix this wire,.
Ii would help you is you have a wiring diagram of your vehicle as the wires are color coded.

Posted on Mar 31, 2013

jturcotte
  • 8980 Answers

SOURCE:

I agree with Phil, but I have given you test procedures for other possible causes, in case the relay is good.

Posted on Nov 22, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What number in 2000 Ford Taurus fuse box is the pcm relay


Doesn't have a number but it is the one with WHT/LT BLU and DK GRN/ORG wires connected to it. The other relay is for fuel pump.

Nov 19, 2016 | Ford Cars & Trucks

1 Answer

Fuel pump/ relay/ wiring issues


They used the jumper wire to make sure that the fuel pump was running. For engine to run you need compression, air, fuel ,ignition.

Your problem lies with either fuel or ignition, and if you dealer cannot fix but continue to charge you, I would suggest you go elsewhere.

Aug 21, 2016 | 2005 Kia Sedona

1 Answer

Just brought 2000 chevrolet venture van have fuel pump isseu but not pump i checked fuse box someone have a small black wire connected to fuel pump fuse and fuel pump relay that blow so i replace both...


It's possible someone used the jumper wire to load side of fuel pump relay, gray wire. That supplies voltage to fuel pump motor, the fuel pump fuse is hot all the time. The fuel pump will run all the time even with key off, running down the battery. They used the jumper because of some kind of problem. Can you unplug the relay and check relay terminals, where the relay plugs in. Use a test light, either a problem on the load or control side of relay. Are the relay terminals numbered, like 30 and 87, maybe 85 and 86 also?
fuel pump-hf4vnnakl4ax4mbzgtumbmbo-1-0.jpg

Sep 06, 2017 | Cars & Trucks

1 Answer

92 ford Taurus fuel pump starts and stops constantly car won't start. replace the relay, I can hear the relay clicking and the pump starting and stopping, any thoughts?


its either a bad fuel pump or you may have to take the fuel pump out and replace the wire that is inside the tank that connects to the fuel pump it is a lead wire and breaks somtimes causing it to have contact and loose contact..hope this helps keep me updated

Mar 28, 2010 | 1992 Ford Taurus

1 Answer

Have a 1997 Ford Taurus GL. 3.0 Liter. 230,000miles. It has been a very reliable vehicle over the years until now. Two weeks ago it began to stall while driving. I made it home and parked in the garage. I...


If you connected a jumper wire to pin 5 and 11 and the fuel pump runs, have you replaced the fuel pump relay in the process? Let me know how it goes.

Feb 16, 2010 | 1997 Ford Taurus

1 Answer

Location of the Horn Relay on a 2005 Ford Taurus Horn doesn't work fuse is Ok and wiring looks good, as well as the horns.


horn may be bad too.

Visual Inspection Chart Mechanical Electrical
  • Horn
  • Horn switch
  • Horn relay
  • Battery junction box (BJB) fuse 101 (60A)
  • Central junction box (CJB) fuses:
    • 216 (15A
    • 230 (15A)
  • Wiring harness
  • Loose or corroded connections
  • Speed control servo or jumper
  • Clockspring
  • Generic electronic module (GEM)


horn relay is in central junction box (fuse panel) under left side of dash.

Nov 03, 2009 | 1999 Ford Taurus

2 Answers

91 ford ranger...fuel pump will not run pump is good


Maybe you need to test the (pcm) power relay, it controls the fuel pump relay. Once the key is turned on the pcm will initialize the power relay, it in turn will turn on the fuel relay for 2 seconds to prime the fuel rail prior to starting. Since the pump runs continuosly, it means the pcm isnt properly grounding the ckt or the relay is faulty.

Oct 14, 2009 | 1991 Ford Ranger Supercab

1 Answer

99 taurus-wont start


pull out the relay and swap it with another one. for example put the relay in your blower motor control spot. if it works relay is good if not it's bad. if you want to see if your fuel pump is working after pulling out the fuel pump relay. use a jumper wire between #30 and #87. where you pulled the relay out and this will hotwire the fuel pump to make sure it's working. have fun!!!

Jul 18, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

84625 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...