What is the rod bearing torque for 1997 Infiniti Q45? And head torque?

https://www.google.com/search?q=Ford+Courier+F8+motor+torque+settings

Torque setting for Ford Courier F8 motor from main bearing

Fixya https://www.fixya.com > Forum > Cars & Trucks > Ford
10 hours ago - Main Bearings Torque specs. 40-43 Ft. Lbs. Cylinder Head Torque specs. 56-60 Ft. Lbs. Read full answer. Oct 05, 2009 • ...

What are the torque settings for a 1997 ford courier 2.2

JustAnswer https://www.justanswer.com > Australian Car Repair
Jul 1, 2021 - Tighten special flywheel-to-crankshaft bolts to 73-87 Nm (54-64 ft. lbs.). 35.If equipped, install clutch disc and clutch pressure plate and ...

1 answer · Top answer: TORQUE SPECIFICATIONS Connecting Rod [https://my.alldata.com/repair/#/repair/vehicle/26150/component ...

1.8 ford courier 8valve torque settings on cylinder head

Fixya https://www.fixya.com > ... > Ford > Expedition
Sep 4, 2008 - First torque value is 58 ft lbs.....then final torgue is 72 ft lbs. Posted on Mar 21, 2009. 0.

Torque Settings

Kiwi Cylinder Heads Ltd https://www.cylinderheads.co.nz > torque-settings
Cylinder Head Torque Settings.

Torque Specifcations

MAHLE Aftermarket https://www.mahle-aftermarket.com > torque3
Make. Liter CID. Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. ACURA. 1.6. 97. D16A1. 86-89. 23 FT/LBS. 40 FT/LBS. 22, 47 FT/LBS.
124 pages
..

1. Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values:

• • Step 1: All to 34 Nm (25 ft. lbs.)
  • Step 2: All to 68 Nm (50 ft. lbs.)
  • Step 3: All to 68 Nm (50 ft. lbs.)

CAUTION: Do not use a torque wrench for the following step.
Step 4: Turn an additional 1/4 turn

• Step 5: Install and tighten bolts (1-10) in sequence shown, to 41 Nm (30 ft. lbs.) .

1. Tighten bolts (1-10) again to 41 Nm (30 ft. lbs.) PLUS 1/4 turn in sequence shown.
2. Install main bearing bedplate to engine block bolts (11-20), and torque each bolt to 28 Nm (20 ft. lbs.) in sequence shown.

Connecting Rod Cap Bolts 54 Nm (40 ft. lbs.) + 1/4 turn
1997 Jetta: Torque settings..vw..the head, fly wheel, big ends.


1997 Jetta3 1800 feul injection


Vibration Damper/belt Pulley
Tighten 20 Nm (14.8 ft lb) Crankshaft Toothed Belt Sprocket Tighten 90 Nm (66 ft lb) + 90° Camshaft Sprocket Tighten 80 Nm (60 ft lb) Main Bearing Cap
Tighten 65 Nm (48 ft lb) FLYWHEEL TORQUE
Torque 60 Nm. (44 ft. lbs.) + 1/4 turn (90°) [1] [1] Always replace bolts.
CYLINDER HEAD TIGHTENING TORQUE [1] :
1st sequence: 40 Nm (30 ft lb)
2nd sequence: 60 Nm (43 ft lb)
Final sequence: plus 1/2 turn (180°)
Here are some additional specifications, thanks
ntake Manifold
Mounting Bolts 25 Nm (18 ft. lbs.) Bearing Cap Nut 20 Nm (15 ft. lbs.) Rod Bearing Cap
Assembly
Tighten 30 Nm (22 ft lb) + 90° To measure radial clearance
Tighten 30 Nm (22 ft lb) but NOT additional 90° TIGHTENING SPECIFICATIONS
Oil Pump Bolt 20 Nm (14 ft. lbs.) Oil Tube To Block 10 Nm (7 ft. lbs.) Exhaust Manifold to Cyl. Head 25 Nm (18 ft lb) Exhaust Manifold to Front Exhaust Pipe 40 Nm (30 ft lb) Water Pump
TIGHTENING SPECIFICATIONS
Cover Bolts 10 Nm (7 ft. lbs.) Mounting Bolt and Studs 20 Nm (15 ft. lbs.) + 1/4 turn (90°) Pulley Bolts 25 Nm (18 ft. lbs.)

TIGHTENING SPECIFICATIONS
Connecting Rod Nuts:
Tighten In Two Stages:
First Stage 30 Nm (22 ft. lbs.) Second Stage turn an additional 90°(1/4 turn)

Hope this helps

https://www.google.com/search?q=1997+ford+explorer+wiper+motor+wiring+diagram&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwjfjN2gmqPVAhUC54MKHf-8DXsQsAQIIQ&biw=1364&bih=642#tbm=isch&q=1997+infiniti+q45+fuse+box+diagram

Could be hub bearing sensor,to fix ,you have to change hub bearing.

1997 Toyota Prado 5VZ-FE
Cylinder head bolts:
Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

I have had good luck with AUTOZONE.com click on repair help and specs. I tried it for your car and it gives the details torque plus turn method . Hope this helps.

Underneath each of the 8 coils

1997 Nissan/Datsun Truck Pickup 2.4L SFI 4cyl

The Main Bearing Cap Torque:
38 Foot pounds (Final torque)

The Rod Bearing Cap Torque:
Torque sequence:
Step 1: Torque to 10-12 Ft/Lbs
Step 2: Torque to 28-33 Ft/Lbs

Hope help with this (remember rated this post). TY for using Fixya.

Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees