Question about Cadillac CTS

1 Answer

How long to replace heater core 2007 Cadillac dts

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 220 Answers

6.9 labor hours.

Posted on Mar 07, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 84540 Answers

SOURCE: 63 cadillac sedan deville heater core removal and installation instructions

I do think you have to pull he dash, for that you will need a manusl, try ebay for used factory manuals, I have had good luck getting them there for all my cars.

Posted on Oct 17, 2008

motor1258
  • 6674 Answers

SOURCE: 2000 Cadillac Escalade. Replace Heater Core

Here you go, Good Luck !! Click on link & scroll down a ways. Any picture will expand if you click on them.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800a5da0

Posted on Jan 28, 2009

  • 1 Answer

SOURCE: heater core

I,M HAVING TROUBLE REMOVING THE COVER PLATE FROM THE HEATER CORE.

Posted on Jan 04, 2010

jturcotte
  • 8841 Answers

SOURCE: dyi instructions for removal/replacement of heater

Please let me know if you have any questions, and thanks for using FixYa.

  1. Drain the engine cooling system.
  2. Remove or disconnect the following: Negative battery cable and Heater hoses from the heater core
  3. Remove the instrument panel as follows: .
    1. Set the parking brake and block the wheels.
    2. Disconnect the parking brake release cable from the parking brake lever.
    3. Unfasten the screws that retain the DLC instrument panel left side sound insulator. Feed the DLC through the hole in the sound insulator.
    4. Unfasten the right side sound insulator panel screws and remove the panel.
    5. Unfasten the screws that attach the instrument panel left side sound insulator to the knee bolster and cowl panel.
    6. Unfasten the nut that attaches the left side sound insulator to the accelerator pedal bracket.
    7. Unplug the remote control door lock receiver module electrical connector.
    8. Remove the door lock receiver module from the left side sound insulator. Remove the left side sound insulator.
    9. Unfasten the screws that attach the instrument panel center sound insulator to the knee bolster, instrument panel, heater assembly and floor duct.
    10. Remove the center sound insulator.
    11. Unfasten the screws that attach the courtesy lamp to the knee bolster.
    12. Unfasten the screws that attach the knee bolster to the instrument panel.
    13. Disconnect the lap cooler duct from the knee bolster.
    14. Unplug the lighter electrical connection and remove the knee bolster.
    15. Unfasten the steering column-to-instrument panel nuts and lower the column.
    16. Unfasten the screws that attach the instrument panel accessory trim plate to the instrument panel.
    17. Remove the trim plate and unplug all necessary electrical connection.
    18. Remove the heater and/or air conditioning control assembly.
    19. Remove the radio and the storage compartment assembly (if equipped).
    20. If necessary, remove the instrument cluster.
    21. Unfasten the left and right instrument panel pivot bolts and the panel lower support bolt.
    22. Unfasten the speaker grilles retaining screws and remove the speaker grilles.
    23. Remove the windshield defroster grille using a flat-bladed prytool. Start at one end of the grille and work your way down the grille.
    24. Unfasten the 4 instrument panel upper support screws.
    25. Tag and unplug all necessary electrical connections.
    26. Remove the instrument panel from the vehicle.
  4. Remove or disconnect the following:

    Air inlet assembly, if equipped , Vacuum hoses Heater assembly studs, from inside the engine compartment, Blower motor resistor Stud from inside the heater case assembly; the stud is located behind the blower motor resistor Heater assembly-to-chassis screws, Heater assembly from the vehicle Access cover screws and cover from the heater assembly Heater core from the heater case assembly
    jturcotte_2224.gif

    Fig. View of the heater case assembly

    jturcotte_2225.gif

    Fig. View of the heater case cover

    jturcotte_2226.gif

    Fig. View of the heater core

    jturcotte_2227.gif

    Fig. Heater core mounting

To install:
  1. Install or connect the following:

    Heater core to the heater case assembly, Access cover to the heater assembly and the cover screws, Heater assembly to the vehicle Heater assembly-to-chassis screws and torque them to 40 inch lbs. (4.5 Nm) Stud, working from inside the heater case assembly; the stud is located behind the blower motor resistor, Blower motor resistor Heater assembly studs, working inside the engine compartment, torque them to 17 inch lbs. (1.9 Nm), Vacuum hoses, Air inlet assembly, if equipped
  2. Install the instrument panel as follows:
    1. Rest the instrument panel on the lower pivot studs.
    2. Attach the electrical connections.
    3. Install but do not tighten the 4 upper instrument panel support screws.
    4. Install the left and right panel pivot bolts. Tighten the bolts to 102 inch lbs. (11.5 Nm).
    5. Install the panel lower support bolt. Tighten the bolt to 102 inch lbs. (11.5 Nm).
    6. Tighten the upper support screws to 17 inch lbs. (1.9 Nm).
    7. Install the windshield defroster grille and the speaker grilles.
    8. Install the radio and storage compartment assembly (if equipped).
    9. If removed, install the instrument cluster.
    10. Install the heater and/or air conditioning control assembly.
    11. Attach the electrical connections to the instrument panel accessory trim plate.
    12. Place the trim plate in position and install its retaining screws. Tighten the screws to 17 inch lbs. (1.9 Nm).
    13. Place the steering column into position and install its retaining nuts. Tighten the nuts to 22 ft. lbs. (30 Nm).
    14. Attach the lighter electrical connection and the lap cooler duct to the knee bolster.
    15. Place the knee bolster into position and install its retaining screws. Tighten the Torx® head screws to 80 inch lbs. (9 Nm) and the hex head screws to 17 inch lbs. (1.9 Nm).
    16. Place the courtesy lamp in position and install its screws. Tighten the screws to 17 inch lbs. (1.9 Nm).
    17. Place the instrument panel center sound insulator in position. Install the screws that attach the center sound insulator to the knee bolster, instrument panel and the floor duct. Tighten the screws to 17 inch lbs. (1.9 Nm).
    18. Install the screw that attaches the center sound insulator to the heater assembly. Tighten the screw to 13 inch lbs. (1.5 Nm).
    19. Install the remote control door lock receiver module to the instrument panel left side sound insulator.
    20. Attach the door lock receiver electrical connection.
    21. Install the nut that attaches the left side sound insulator to the accelerator pedal bracket. Tighten the nut to 35 inch lbs. (4 Nm).
    22. Install the screw that attaches the left side sound insulator to cowl panel. Tighten the screw to 13 inch lbs. (1.5 Nm).
    23. Install the screws that attach the left side sound insulator to knee bolster. Tighten the screw to 17 inch lbs. (1.9 Nm).
    24. Feed the DLC through the hole in the sound insulator, place the DLC in position and install its retaining screws. Tighten the screws to 21 inch lbs. (2.4 Nm).
    25. Install the right side sound insulator and tighten the screws
    26. Connect the parking brake release cable to the lever

  3. Install the heater hoses to the heater core.
  4. Refill the cooling system.
  5. Connect the negative battery cable.
  6. Run the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Posted on Sep 11, 2011

  • 1 Answer

SOURCE: I need to replace the heater core in my 94 cadillac eldoeado

Heater core replacement instructions

Posted on Jan 01, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 dts caddy blower motor resister location


Your not going to like to hear this , but you'll need to take the dash apart !
Blower Motor Resistor Replacement
Preliminary Procedure
  1. Remove the HVAC module. Refer to HVAC Module Assembly Replacement .
Preliminary Procedure
  1. Drain the cooling system. Refer to Cooling System Draining and Filling .
  2. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
  3. Remove the evaporator tube from the thermal expansion valve. Refer to Air Conditioning Evaporator Hose Assembly Replacement .
  4. Remove the heater hoses from the heater core. Refer to Heater Hoses Replacement .
  5. Remove the brake pedal bracket assembly. Refer to Brake Pedal Assembly Replacement .
  6. Pull back and reposition the carpet.
  7. Remove the lower instrument panel (I/P) support brace. Refer to Instrument Panel Center Support Bracket Replacement .
  8. Reposition the auxiliary air distribution duct. Refer to Auxiliary Air Distributor Duct Replacement .
  9. Remove the instrument panel carrier. Refer to Instrument Panel Carrier Replacement .
  10. Disconnect the HVAC module assembly electrical connectors.
1
HVAC Module Assembly Nut (Qty: 5)
Tip
Tighten the nuts in sequence.
Tighten
9 N?·m (80 lb in)
2
HVAC Assembly Module
Disconnect the blower motor resistor electrical connector.

Jul 28, 2016 | 2008 Cadillac Dts

1 Answer

How do I reset the onstar system on a 2007 Cadillac DTS


Activate Pre-Owned Vehicle ' OnStar

https://www.onstar.com/preowned
OnStarRequires factory-installed and enabled remote start. Requires automatic ... Visitonstar.com for vehicle availability, coverage map, details and system limitations.

[PDF]Cadillac DTS 2007.pdf - costartech.com

www.costartech.com/pb/.../Cadillac/DTS/Cadillac%20DTS%202007.pdf
Feb 9, 2012 - 2007 Cadillac DTS ' DTS (VIN K) Service Manual ' Driver Information and ... the keypad will NOT reset this version of the OnStar® system.

Nov 04, 2015 | Cadillac Cars & Trucks

1 Answer

How do I replace the rack and pinion on a 2007 Cadillac DTS?


You go to a dealer - this is a MAJOR repair job involving special tools and moving the engine out of the way.

Sep 16, 2014 | 2007 Cadillac DTS Sedan

1 Answer

Wet carpet on front passenger 2010 cadillac dts


If the water is clear, chances are its from the air cond. If it is oily, it could be coolant leaking from the heater core.
If it is still covered under factory warranty I would have the dealer take a look.

Apr 06, 2013 | 2010 Cadillac DTS

2 Answers

2007 Cadillac dts cigarette lighter fuse


You will find all the fuses under the back seat driver side.

Jun 18, 2012 | 2007 Cadillac DTS Sedan

1 Answer

Why cadillac 2007 DTS does not get start


Are you sure you added oil?If you did here is the oil lever sensor you will need.3_25_2012_11_52_20_pm.jpg

Mar 25, 2012 | 2007 Cadillac DTS Sedan

1 Answer

I have a 2007 cadillac dts when do i need to get the timeing belt replaced


60,000 miles is generally the point to change a timing belt. Don't put if off, the damage due to a broken or jumped timing belt can be astounding.

lp

Dec 28, 2010 | 2006 Cadillac DTS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

84524 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...