2015 GMC Acadia "service stabilitrak" and "engine power reduced"

check codes also no stablitrak fuse

Not sure why you said "is this for all vehicles"? Who are you talking to? This is your only post here. If you see 'Suggested Answers', that is the software GUESSING an answer.

You are not the only one with this issue

Service Side Detection System - SBZA ' GMC Acadia Forum

https://www.acadiaforum.net > ... > General Tech

Dec. 3, 2014 - 2013 Acadia Denali, AWD, White Diamond Tri-coat ... Joined Apr 13, 2015 ... Although they said the side detection module is located on the ... Blind Spot Detector Failure Safety Issue
Oct. 1, 2018
Airbag light and service message fixed
Oct. 13, 2016
Passenger seat air bag on off problem
Feb. 5, 2020
Service airbag
Jan. 9, 2020
More results from www.acadiaforum.net

2015 GMC Acadia/Acadia Denali Owner Manual - Owner's ...

https://my.gmc.com > 2k15acadiaden2ndPrint

PDF GMC Acadia/Acadia Denali Owner Manual (GMNA-Localizing-U.S./Canada/. Mexico-7576030) ... is located on the left side of the steering ... See Forward Collision Alert (FCA). System on ... the airbag modules, the wiring, and the crash sensing and diagnostic module. For more ... occurs with the All-Wheel Drive. (AWD) ...

Could be rusted and broken because have others codes you should check for new codes.

StabiliTrak Indicator Light: If the warning light does not come on then, have it fixed so it will be ready to warn you if there is a problem. If it stays on, or comes on when you are driving, there may be a problem with your StabiliTrak system and your vehicle may need service. When this warning light is on, the system is off and will not limit wheel spin. Adjust your driving accordingly.

This light will also flash when the StabiliTrak system is active. If the StabiliTrak system warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service.

The traction control part of StabiliTrak can be turned off by pressing and releasing the StabiliTrak button if both systems (traction control and StabiliTrak) were previously on. To disable both traction control and StabiliTrak, press and hold the button for five seconds.

Traction control and StabiliTrak can be turned on by pressing and releasing the StabiliTrak button if not automatically shut off for any other reason.

When the TCS or StabiliTrak system is turned off, the StabiliTrak light and the appropriate TCS off or StabiliTrak off message will be displayed on the DIC to warn the driver. Your vehicle will still have brake-traction control when traction control is off, but will not be able to use the engine speed management system.

If the StabiliTrak and/or Traction Control are not operating properly, I encourage you to take your vehicle in for inspection. A certified technician will be able to offer a more accurate diagnosis.

Best to have the vehicle checked out by a mechanic if it comes back on. Also if you where driving in wet weather that's a possible reason for the light to display. Al s of double che c k air pressure in tire all the way around the vehicle

here is a little help. if you need more I am on facebook. There are 2 ignition 1 voltage circuits supplied to the Engine Control Module (ECM). The first ignition circuit is provided by the powertrain relay, through a fuse. This ignition 1 voltage circuit supplies power to all the internal ECM circuits associated with the throttle actuator control (TAC) operation. The second ignition 1 voltage circuit is supplied by the run/crank relay through a fuse, and is used to power the remaining internal ECM circuits. If the ECM detects a voltage difference between the 2 ignition 1 voltage circuits, DTC

i have the same gmc acadia 08 and same problem .its bad crankshaft position sensor. i put new one it and now everything good

{: ) A car swerving light on the instrument cluster is the StabiTrak indicator, sometimes called the traction control indicator. A wrench beside it tells it requires servicing.

Your vehicle is equipped with StabiliTrak, which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions.
Traction control activates when the controller senses wheel spin. StabiliTrak will selectively apply the brakes and reduce engine torque to help regain traction.
Stability control activates when the controller senses a discrepancy between your intended path and the direction the vehicle is travelling. StabiliTrak selectively applies braking pressure at any one of the vehicle's brakes to help guide the vehicle in the direction which you are steering.
When you first start your vehicle and begin to drive away, the system performs several diagnostic checks to insure there are no problems. You may hear or feel the system working. This is normal and does not mean there is a problem with your vehicle. If driving conditions delay system initialization, the STABILITRAK NOT READY message may be displayed. If this is the case, your vehicle does not need servicing.
When the StabiliTrak system is both on and actively controlling the stability of the vehicle, the StabiliTrak light will blink for the duration of the event.
You may also feel or hear the system working. This is normal.
StabiliTrak will turn off automatically if a problem is detected in the system. The StabiliTrak light will come on and SERVICE STABILITRAK will be displayed on the DIC. For vehicles without a DIC, the StabiliTrak light and the StabiliTrak service light will both come on. If the SERVICE STABILITRAK message (or StabiliTrak service light) does not clear itself after restarting the vehicle, you should see your dealer for service.

{: ) Your stabilitrak system may not work properly. The vehicle need to be scanned for trouble codes. In case you get a C0196 code, the recommendation is to reprogram the electronic brake control module. I hope that's the only cause.

This is your cars computer warning you she needs attention. Most vehicles with complex systems require the auto dealers computer to decode these messages and reset the system after the worn part is replaced and or necessary adjustments are made. I hope this helps you.