Vacuums Logo

Related Topics:

A
Anonymous Posted on Feb 22, 2019

My eyevac sensor works then i wait 5 seconds and go to use it again and it won't turn on. I have to wait 5 minutes then it works again

1 Answer

Derrick Schultz

Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

  • Master 11,405 Answers
  • Posted on Feb 23, 2019
Derrick Schultz
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

Joined: Jan 17, 2019
Answers
11405
Questions
0
Helped
2328302
Points
23972

You can get guide from many sites.. i know few
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassemb ly, complete refurbish, repair, installation every single t hing is covered
within seconds u can get the access and it's totally illustrative complete

4 Related Answers

Anonymous

  • 34 Answers
  • Posted on Aug 11, 2009

SOURCE: MY GEO TRACKER SHUT DOWN AFTER 3 MINUTE. I WAIT 5 MINUTE MORE

You seem to know enough about cars to rule out the obvious, like no gas, no spark.

If the tracker dies at stop signs or traffic lights, but you can start it and run it in between for a while, it could have an ECM failure, common for this age and year of tracker. Your symptoms are not exactly the same, but you may want to investigate this if nothing else works.

For more information on ECM failures google 'Geo Tracker ECM Failure'. The module can be purchased (rebuilt) on Ebay for about a hundred bucks. I have no affiliation with the guy that sells them.

Ad
stevexmas007

Steve Christmas

  • 699 Answers
  • Posted on Mar 27, 2011

SOURCE: truck star ok run for

do you smell any fumes?

jayhawke

Jim Y

  • 338 Answers
  • Posted on Jul 30, 2011

SOURCE: Engine won't start when it's

try running a good injector cleaner thru it- sounds as if you have a(or a couple)weeping injector,
try LUCAS injector cleaner- works on my sonoma

danoyachtcap

danoyachtcap

  • 2907 Answers
  • Posted on Mar 30, 2015

SOURCE: 1994 Honda Accord often won't restart after it stalls. After waiting 5-10 minutes it starts up again fine. What is causing this?

Could also be an intermittent coil, due to loose connections in the distributor.
Hope this helps.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My problem/// cleaner turns on for a around ten (10) seconds and then shuts off wait a few minutes and it will turn on but goes off again at ten (10) seconds?????

These units have a automatic resetting thermal fuse near the motor to help to protect it from burning up by running too hot. This will need to be inspected and tested to see if it's holding it's proper temps., if not it will have to be replaced. There should also be an inspection of the machine to detect what was causing the reset to shut down that quickly, so that can be repaired as well.
0helpful
1answer
0helpful
1answer

My Kenmore vacumn won`t turn on . worked fine one minute then stopped. The light works on the handle but no vacumn

You probably have a sensor that needs attention and is clogged up so unclog and see if that takes care of it
1helpful
1answer

DC 17 UPRIGHT BRUSH MOTOR WONT STAY RUNNING. TURN

have a look at the filters first as it sounds like you blokeage
2helpful
1answer

Stops after a few minutes

Its overheating, so the TOC (thermal overload cutout device) is cutting the power to the motor to protect it.
Thats why it works when it has cooled down.
Check for blockages and make sure the filters are clean, if it still happens take to an approved engineer to check the TOC
1helpful
1answer

Protection light

it might be the bag or the sensor inside the machine.
0helpful
1answer

Dyson dc07 animal

This is from the Dyson web page:
Get expert help Thermal cut out Most Dyson vacuums have a built in safety system that stops the machine if it begins to overheat. This usually happens because the filter needs washing or your machine is blocked. If your machine turns off on its own, unplug it and leave it for at least an hour to cool down. Remember to check the filter and look for blockages before re-starting.
Any non- domestic use may adversely affect the filter performance such as vacuuming up plaster dust.


Sounds like your vacuum is overheating. Check the above.


Lou

Not finding what you are looking for?

174 views

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Anonymous

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...