Question about Ford Cars & Trucks

2 Answers

2005 ford five hundred, the battery was completely drained for a month, after replacing the battery the car starts and runs for a few seconds then dies

Posted by on

  • Arnie Burke
    Arnie Burke Feb 15, 2019

    Alternator cud b worn or the main wire from it to batt is old causing bad flow. Ur fuel pump or ptessure regulator mite hav problms or gas is old or tainted

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 60,507 Answers

CHECK YOUR FUEL SUPPLY FILTER , PUMP ETC

Posted on Feb 15, 2019

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 19 Answers

Is your battery drained? Check it with a multimeter. If not then it’s likely the fuel pump.

Posted on Feb 15, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 2006 Ford Five Hundred -- Where's the fuel filter?

right rear just in front of wheel. push clips back and remove old filter. apply new filter insuring flow is correct direction by arrow on filter press the clips back in place and you are ready. check to see if it is leaking.

Posted on Mar 16, 2009

  • 93 Answers

SOURCE: Backup sensors not working

using a mechanics stethoscope..you can listen to the sensors...listen for the weakest sensor and replace it...the sensors make a faint ticking noise when listened to..the faulty sensor will be noticeably different sounding than others...of course the key need to be in on position and in revers (be careful not to run you self over!)

Posted on Jun 02, 2009

  • 1 Answer

SOURCE: I have a 2005 Ford five hundred and the

You need to have the transmission serviced. The wrench indicates that the fluid in your transmission is out of spec or you have an out of spec pressure condition.

Posted on Oct 12, 2009

subikid90
  • 180 Answers

SOURCE: electric cooling fan on ford five hundred not

Check the fuse for the fan and you could test to see if you have a voltage running to the fan when the car starts to overheat. If you have no power to the fan then trace the wore and see if you cant find the problem. If you have power then the fan motor is most likely bad.

Posted on Mar 03, 2010

  • 3 Answers

SOURCE: The torque strut replacement

.ok

Posted on Dec 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the speed sensor located?


    2005-2007 Ford Five Hundred Speed Sensor - JC Whitney

    www.jcwhitney.com/2005...ford-five-hundred/...speed-sensor...speed-se...
    Shop for a 2005-2007 Ford Five Hundred OE Replacement Vehicle Speed Sensor by Motorcraft with a 30-day Satisfaction Guarantee at JC Whitney, America's ... images for 2005 Ford Five Hundred Where is the ...

Nov 26, 2015 | 2005 Ford Five Hundred

1 Answer

How do i replace rear plugs on 2005 ford five hundred ?


Jack up the car, put it on jack stands and then slide under it.

Sep 11, 2014 | 2005 Ford Five Hundred

1 Answer

2006 ford five hundred headlights brighten every 5 seconds


Sound like a bad ground somewhere but it is strange its every five seconds. See if you can hear a relay clicking somewhere under the hood or dash.

Dec 14, 2013 | 2006 Ford Five Hundred

2 Answers

My ford five hundred won't turn over the lights are on but when i turn the key to start nothing happens this is after it sat for 8 months and the battery went dead. I charged the battery completely and the...


the battery is probably badly sulphated and has cell problems
use a load tester to check the battery
after that use a scan tool to reset the ECM program as the CPU is corrupted

Jan 29, 2018 | 2006 Ford Five Hundred

1 Answer

005 ford five hundred with code po942


You have a shop with no data base such
as Alldata,Mitchell or Identifix !!

Mar 06, 2013 | 2005 Ford Five Hundred

1 Answer

Problem with my ford five hundred fuse


Might be a grounding issue checck your connections

Aug 28, 2012 | 2005 Ford Five Hundred

1 Answer

Program new key fob for a ford fivehundred


You are in luck, a 2005 Ford Five Hundred Key Fob Remote is self programmable. Now these procedures can be a bit frustrating at times, so be patient, it's all about timing. If you get it programmed on the first try you are among a very few talented programming individuals! Also, if you need an affordable key fob replacement for your Ford Five Hundred, buy it here:
https://www.keylessentryremotefob.com/Ford-Five-Hundred-Remotes-and-Keys-s/5167.htm

Here are the programming instructions:

FORD REMOTE - THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don't press the brake pedal at any time during or before the procedure.
Procedure A:
1.Close all doors, then open drivers door and press the Unlock button on driver's door while it is open, insert key into ignition.
2.Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1)
(Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
3.Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
4.Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
5.Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
1. Fasten seatbelt and close all doors
2. Turn the ignition from OFF to RUN 4 times within 3 seconds.
3. Turn the ignition OFF. The system will chime to confirm programming mode.
4. Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
5. Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
6. Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.


4001-ford-image-1-44ys2bzxdezw1orb312ruqfb-2-0.jpg oucd-4b-image-1-44ys2bzxdezw1orb312ruqfb-2-2.jpg

Mar 27, 2012 | 2005 Ford Five Hundred

1 Answer

2005 Ford Five Hundred - Cold Start Problems


try to change spare plugs,if wont not halp go to local garage.

Mar 06, 2012 | 2005 Ford Five Hundred

1 Answer

Backup sensors not working


using a mechanics stethoscope..you can listen to the sensors...listen for the weakest sensor and replace it...the sensors make a faint ticking noise when listened to..the faulty sensor will be noticeably different sounding than others...of course the key need to be in on position and in revers (be careful not to run you self over!)

May 26, 2009 | 2005 Ford Five Hundred

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...