Was it a brand new transponder key and you have a working transponder key? You have to have a working key to make a duplicate. And not all transponder keys are programable if its has been already been assign a code before. Toyota will send you a new key and transponder unit free only problem is that it gets sent to a local dealership only and they charge to install it.
SOURCE: central locking system stopped working
If the A6 layout for the modules is the same as my A4, the lock pump is in the rear corner of the car, on the passenger side. In the trunk, pull up the carpeting behind the passenger rear wheel, and tucked down in there is the pump assembly. They're known to go bad and it's a pretty likely cause for your problem, provided your fuses are not blown.
SOURCE: Remote door opener... key fob
Are the OTHER remotes working properly? If so, there is no wiring issues. It is rare that wiring can cause the remotes to be inoperative...Sadly, I have observed many remote/fobs that simply fail. I would advise both of you to take your fobs to your local Toyota dealer, and have the Service Dept check the RF output from the remotes on their hand-held detector. This is the only way to determine if the fob/remote is indeed working. No RF = no lock/unlock. All Toyota dealers should have this box, it is a required special tool. The part number for the detector is 00002-09001-01
SOURCE: remote key fob won'tprogram
1-insert and remove key from ignition two times
2-close and open driver door two times
3-insert and remove key once from ign.
4-close and open drvr door twice
5-insert key into ign.,then close driver door
6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.
7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.
8-press lock/unlock together and hold for a second
9-release,and press lock on remote,the door locks will cycle
confirming program.continue to do other remotes you have,steps 8 and
9.if only one in possession,you are done. To end mode open door or insert key into ignition.
You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works
SOURCE: 2004 Toyota Camry key fob programation
sit in car all doors closed put key in ignition and turn from OFF to ACC 3 times as fast as you can leaving it in ACC on the last cycle then press your remote button. your blinkers should flash to tell you this has worked.... may take you a couple of tries to get it!!
SOURCE: 08 dodge ram key FOB reprogramming
ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you. 2. Fasten your seat belt ( fastening the seat belt will cancel any chiming that may 3. Place key into the ignition. 4. Turn the ignition to the ON position ( DO NOT START THE ENGINE ) 5. Press and hold the UNLOCK button on a working remote. 10. Within 4 seconds of hearing the chime, press and release any button on the remote
Click here to find a Locksmith in your area to program this remote.
1. Enter your vehicle and close all doors.
confuse you during this programming procedure.)
6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than
10 seconds, then press and hold PANIC button.
7. When a single chime is heard, release both buttons. The chime indicates the system
is in program mode.
8. Press and release both the LOCK and UNLOCK buttons, simultaneoulsly on the remote
to be programmed.
9. A single chime will be heard. The chime indicates the the remote was recognized.
being programmed.
11. A single chime will be heard The chime indicates the remote has been programmed.
12. Repeat steps 8 to 11 for a total of 4 remotes.
13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode.
http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html
----------After getting car
washed, check engine light is ON and key less entry not working, tried
reprogramming. Also car shows fuel pressure?
http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html
-----------Audi A8 Key Fob Programming?
http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html
----------------
Oldsmobile Aurora Key Fob Reprogramming?
http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html
-------------
Buick Lesabre Key Fob Reprogramming?
http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html
---------------
Keyfob remote not working on 2003 Ford E350 Econoline?
http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html
-----------
KeyFob will open the doors but not start on BMW?
http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html
------------
Mitsubishi Car Key Not getting detected after replacing ECM
http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html
-----------
Key Fob will not lock and unlock doors?
http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html
-------------
2000 Jeep Cherokee Limited: KeyFob Remote Not
Working?
http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html
-----------
Chevrolet Malibu: Key Stuck in ON position?
http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html
-----------
Theft indicator not letting car to start?
http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html
-------------
2012 Dodge Ram: Ignition Key will not
release?
http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html
--------------
These details will help.Thanks.
2. Fasten your seat belt ( fastening the seat belt will cancel any chiming that may
confuse you during this programming procedure.)
3. Place key into the ignition.
4. Turn the ignition to the ON position ( DO NOT START THE ENGINE )
5. Press and hold the UNLOCK button on a working remote.
6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than
10 seconds, then press and hold PANIC button.
7. When a single chime is heard, release both buttons. The chime indicates the system
is in program mode.
8. Press and release both the LOCK and UNLOCK buttons, simultaneoulsly on the remote
to be programmed.
9. A single chime will be heard. The chime indicates the the remote was recognized.
10. Within 4 seconds of hearing the chime, press and release any button on the remote
being programmed.
11. A single chime will be heard The chime indicates the remote has been programmed.
12. Repeat steps 8 to 11 for a total of 4 remotes.
13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode.
209 views
Usually answered in minutes!
×