I replaced the touch screen in my Cadillac SRX upon re installing it there is no power to the unit but all three connections at the back are plugged in
Sound like you've blown a fuse, check the owners manual for the location of your fuse and check it out, if that doesn't work get back to me!
If this helps please let me know by clicking the green helpful icon, if you would leave a few words as a review or recommendation that would be greatly appreciated! It lets me know if I'm doing well or not so all feedback is appreciated. Just a few words would be quite helpful if you think this answer is helpful. Have a great day and good luck, you'll get this and now you can help anyone who has this issue!
SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX
wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.
SOURCE: Changing fuel filter on 2004 Cadillac SRX
If you go to the auto parts store they should have a fuel line disconnect tool that has a 5/16ths end an a 3/8ths end. The tool is shaped like an X. Before you start you need to pull the fuel pump fuse under the front of the REAR passenger side seat while the car is running and let it stall. it will release the built up pressure. This is important unless you want gas to spray every where. Then take the tool and start with the end of the filter with two lines. Place the appropriate end of the tool over the smallest inlet, push the tool in then pull the line towards the filter and then push the line away and it should disconnect. Do the same with line above. Then you can use the two appropriate size wrenches to disconnect the outlet end. reconnecting the new filter is simple just make sure your quick connect lines click in all the way and you tighten the outlet line well, I think its like 22 or 25 ft/lbs.
SOURCE: how do you replace license
Hi,
First you have to take out the one and only screw in the rear
hatch door - it's where the hand pull down is you use to close the
hatch.
Then you have to pop all the plastic clips all the way
around the plastic door panel, trying not to pull them out from the
frame . If you do pull out the white plastic plugs from the frame you
better make certain you take them off the plastic housing and insert
them back into their frame holes - or you will never get the housing
back on.
Once you have the housing loose disconnect the inside
tail gate light wire to remove the whole thing. Then you have to remove
7 to 8 nuts from the back of entire License plate, back up bulb housing
using a deep socket to get in there. Work it loose from the rear of the
car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.
Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.
Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.
OPTIONAL:
Once you take out the bulbs you might see that
the housing is melted where the bulb wanted to burn through. Drill two
small holes one is each end of the housing before I put everything back
together to release some of the heat.
Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.
The bulbs come in a two pack of cost $4.95 .
Take care
SOURCE: 2004 Cadillac srx key stuck in ignition and loss of power
if the battery is dead then the key will not come out hook up a another car with jumper cables then it will come out
497 views
Usually answered in minutes!
×