Question about 2005 Suzuki Forenza

1 Answer

How to tighten the timing belt tensioner on suzuki forenza 2005

I put the tentioner on but the belt won't thighten

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 297 Answers

I am pretty sure the tensioner is not adjustable. It sounds like you may not have the belt in the right place. Or if you replaced it, make sure you have the correct belt.

Posted on Jan 23, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
boysor2933
  • 293 Answers

SOURCE: 2005 suzuki forenza My car will not start up.

Check if the kill switch is engaged. Check for faulty starter solenoid or disconnected solenoid wire. Check for defective ignition switch. Check for defective starter motor.

Posted on Aug 10, 2009

  • 93 Answers

SOURCE: 2005 Suzuki Forenza timing belt breakage

hi im not sure on this particular model but there a few easy ways to check.... take the spark plugs out, remove the broken belt, shine a light down the holes and look for dammdge, if you cant see anything you can turn the crank but it is a tricky job because you can ruin the engine so if your unsure get a mechanic to do it.. or your other alternative is to remove the head and have a look but you will need a new head gasket kit, timing belt and tensioner kit etc .. it is important that you do not turn the engine over when the belt is disconected in any way UNTIL you know for sure that valves wont hit pistons, even bending a valve will not be very noticable but when its all back together you will deffinately notice and will have to pull it all back apart

Posted on Feb 10, 2010

Testimonial: "Really Fast Reply with very good information. THANKS!!"

  • 90 Answers

SOURCE: I WANT TO KNOW THE TIMING MARKS FOR SUZUKI FORENZA

just mark the pulleys with tip-ex ,same thing and youd be finished in half the time

Posted on Feb 21, 2010

tgv1501
  • 870 Answers

SOURCE: where do you put transmission fluid in my 2005

it goes from the dipstick. Can you locate the dipstick?

Posted on Dec 28, 2010

emissionwiz
  • 84540 Answers

SOURCE: how to change timeing belt on 2008 suzuki forenza

Instructions

    • Disconnect the negative cable on your car battery. Make sure to wait for the engine of your Suzuki Forenza to cool off completely before you start working on it.
    • 2Rotate the engine using a wrench attached to a crankshaft bolt. Align the timing mark on the pulley to the 0o mark on the scale.
    • 3
    • Remove the screws and the bolts that hold the timing cover in its place and take the cover off. Loosen the bolts that hold the spring-loaded tensioner of the timing belt a little. Pull the tensioner away from the timing belt and then tighten the bolts again.
    • 4Pry off the timing belt from the pulley channels and the camshaft sprocket with a flat head screwdriver. Set the old timing belt aside and compare it with the new belt. The new belt should have the same width as with the old timing belt and the inside surface of both belts should have the same size of teeth.
    • 5Put the new timing belt on the sprockets and make sure it is positioned correctly. Loosen the bolts that hold the tensioner and pull the tensioner toward the timing belt.
    • 6Adjust the timing of the belt. Strictly follow the instructions on the Suzuki Forenza manual. When the timing is set, check if the timing marks on the can, crank and sprockets are still aligned.
    • 7Turn the engine with the wrench on the crankshaft pulley two whole circles until you reach the 0o mark.
    • 8Reinstall the timing cover and tighten the screws and bolts that hold the cover in its place.
    • 9Reconnect the negative cable on your car battery. Put the key in the ignition and start the car to check if the timing belt replacement was successful and that the car is running properly.

Posted on Jun 25, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing procedure for 2005 suzuki forenza


what engine, most cars have many choices new.. what is yours.
"Displacement or VIN"
cam
or
spark?
btw its really a Daewoo Lacetti from S.Korea makers.
by a real FSM.
or got to alldata.com and read

here is the list of engines
1.4 L 93 bhp (69 kW) Petrol I4
1.6 L 109 bhp (81 kW) Petrol I4
1.8 L 120 bhp (89 kW) Petrol I4
2.0 L 132 bhp (98 kW) Petrol I4
2.0 L 121 bhp (90 kW) Petrol I4
2.0 L 121 bhp (90 kW) Diesel I4

before working on any car, engines. in the USA (where you?)
open hood, look up see that vacuum and smog tag there
and it tells you what engine you have,
than ask questions based on that.

the USA forenza uses the
The US model line features the 2.0 L 4-cylinder E-TEC II made by General Motors, developing a maximum power of 132 horsepower at 5600 rpm.

this is a DOHC engine, 2 cams
and a belt (rubber band engine)
cam timng, im not repeating the 38 steps in the manual or torques/
but the crank cog mark is down aligned with the bottom pan mark
the cams are both at 12pm, aligned with markes on back top pan.

install (cut and past just first 8 steps) 2.0L E-tec II only)
  1. align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover.
  2. Align the timing marks on the camshaft gears, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
  3. Install the timing belt.
  4. Turn the hex-key tab in a clockwise direction to tension the belt. Turn until the pointer aligns with the notch.
  5. Install the automatic tensioner bolt and tighten to 18 ft. lbs. (25 Nm).
  6. Rotate the crankshaft two full turns clockwise using the crankshaft pulley bolt.
  7. Recheck the automatic tensioner pointer.
  8. Install the front timing belt cover.




Nov 27, 2013 | 2005 Suzuki Forenza

1 Answer

Timing belt tentioner keeps loosing up


Sounds to me like the belt tensioner needs replacing.When you do this check all other idlers and water pump.Fit new belt..Good-luck....

Jan 05, 2013 | 2004 Suzuki Forenza

1 Answer

How to change timeing belt on 2008 suzuki forenza


Instructions
    • Disconnect the negative cable on your car battery. Make sure to wait for the engine of your Suzuki Forenza to cool off completely before you start working on it.
    • 2Rotate the engine using a wrench attached to a crankshaft bolt. Align the timing mark on the pulley to the 0o mark on the scale.
    • 3
    • Remove the screws and the bolts that hold the timing cover in its place and take the cover off. Loosen the bolts that hold the spring-loaded tensioner of the timing belt a little. Pull the tensioner away from the timing belt and then tighten the bolts again.
    • 4Pry off the timing belt from the pulley channels and the camshaft sprocket with a flat head screwdriver. Set the old timing belt aside and compare it with the new belt. The new belt should have the same width as with the old timing belt and the inside surface of both belts should have the same size of teeth.
    • 5Put the new timing belt on the sprockets and make sure it is positioned correctly. Loosen the bolts that hold the tensioner and pull the tensioner toward the timing belt.
    • 6Adjust the timing of the belt. Strictly follow the instructions on the Suzuki Forenza manual. When the timing is set, check if the timing marks on the can, crank and sprockets are still aligned.
    • 7Turn the engine with the wrench on the crankshaft pulley two whole circles until you reach the 0o mark.
    • 8Reinstall the timing cover and tighten the screws and bolts that hold the cover in its place.
    • 9Reconnect the negative cable on your car battery. Put the key in the ignition and start the car to check if the timing belt replacement was successful and that the car is running properly.

Jun 25, 2012 | Cars & Trucks

1 Answer

I replaced the timing belt on a 05 suzuki forenza and not i cannot figure out which mark to use on the exhaust cam pulley


  • Hear are the timing marks fora a 2005 Suzuki Forenza 2.0

  • Crankshaft gear to the bottom of the rear timing belt cover ----


ironfist109_352.jpg


  • Camshaft gear to Camshaft cover ---

ironfist109_353.jpg


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 10, 2011 | 2005 Suzuki Forenza

1 Answer

2005 Suzuki Forenza timing belt breakage


hi im not sure on this particular model but there a few easy ways to check.... take the spark plugs out, remove the broken belt, shine a light down the holes and look for dammdge, if you cant see anything you can turn the crank but it is a tricky job because you can ruin the engine so if your unsure get a mechanic to do it.. or your other alternative is to remove the head and have a look but you will need a new head gasket kit, timing belt and tensioner kit etc .. it is important that you do not turn the engine over when the belt is disconected in any way UNTIL you know for sure that valves wont hit pistons, even bending a valve will not be very noticable but when its all back together you will deffinately notice and will have to pull it all back apart

Feb 10, 2010 | 2005 Suzuki Reno

1 Answer

Need diagram for serpentine belt


2004 SUZUKI FORENZA - L4 2.0L 2000cc GAS FI N

Adjustment

The belt is automatically adjusted by the auto tensioner.


Drive Belt Routings

47cc840.jpg

Fig. Accessory drive belt routing-2.0L engine



Removal & Installation
  1. Remove the air filter housing assembly bolts and the air intake tube.
  2. Remove the air filter housing assembly from the vehicle.
  3. Use a wrench to turn the tensioner bolt clockwise, compressing the tensioner, and releasing the tension on the serpentine accessory drive belt.
  4. Remove the serpentine accessory drive belt.
To install:
  1. Use a wrench to turn the tensioner bolt clockwise, compressing the tensioner, and releasing the tension on the serpentine accessory drive belt.
  2. With the wrench in place on the tensioner bolt, loop the serpentine accessory drive belt loosely over the pulleys.
  3. Slip the belt over the tensioner.
  4. Remove the wrench from the tensioner bolt and the belt will tighten itself.
  5. Install the air filter housing assembly into the vehicle.
  6. Install the air intake tube and the air filter housing assembly bolts.
  7. Tighten the air filter housing assembly bolts to 53 inch lbs. and nm
I really hope helped with this. remember rated this help. Good luck.


Nov 12, 2009 | 2004 Suzuki Forenza

1 Answer

I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

Sep 21, 2009 | Hyundai Elantra Cars & Trucks

Not finding what you are looking for?
2005 Suzuki Forenza Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

84524 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...