Question about Mercedes-Benz Cars & Trucks

Open Question

2010 c180 compressor light not working took out the light switch nex to ignigtion but how would i know if that is the problam an not a relay unit.

Posted by on

  • Arnold Lott
    Arnold Lott Jan 03, 2019

    Hi vernon , I want to help you with your question, but I need more information from you. Can you please add details in the comment box? Is it only one light or all your lights. Also give the Vin no. of your car. Please check fuses 18,29 and 30.

×

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ryanlutton
  • 1238 Answers

SOURCE: my problam gmc model 2006 coming

P1682 is low voltage at the ignition switch. 2 things, our ignition switches are prone to go out in Trailblazers and Envoys, so I'd look to replace this first. The only other problem would be wiring harness that leads to the ignition, check for shorts. My bet is the switch, it's not the switch the key goes into, it's under the column cover on the bottom, a little black module. Very easy to take it out and replace yourself and will run you around $35.

Posted on May 31, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have indica dls 2010 car. compressor is not switcing on even i swith on the ac button . i disconnect the compressor wire and connected a wire from battory (+)to compressor. the compressor is on but even...


Hi Ravi,

yes when you connected the + wire to battery it wont turn off by using ac switch.
please un do the thing you done.
i think the problem is your system is out of gas or gas pressure drops required level.or bad timer relay unit .
the system has pressure cut out and if you are out of gas it shuts down the compressor and it is safty for compressor too.

regards,
nuwan

Jan 13, 2014 | Tata Indica Cars & Trucks

2 Answers

Looking for left headlight relay location on 2004 c240


dont know what model or age this merc is but i have a 1994 c180 and that has relays for the head lights they are in fuse box have you checked conections and bulb does the rear lights come on y/n same side or a faulty switch but dont think its this

Oct 17, 2012 | Mercedes-Benz C240 Cars & Trucks

1 Answer

Daytime running lights are not working. The regular headlights are though. The light symbol on the driver's side keeps blinking to let me know the daytime running lights are out. i swiched all the


There is a microprocessor in the instrument cluster that grounds the DRL relay - do you know if the relay has power from the headlight fuses and is being grounded by the processor ?

Aug 23, 2012 | Pontiac Sunfire Cars & Trucks

1 Answer

My problam gmc model 2006 coming cde p1682 nex car not start watis solution pleas help


P1682 is low voltage at the ignition switch. 2 things, our ignition switches are prone to go out in Trailblazers and Envoys, so I'd look to replace this first. The only other problem would be wiring harness that leads to the ignition, check for shorts. My bet is the switch, it's not the switch the key goes into, it's under the column cover on the bottom, a little black module. Very easy to take it out and replace yourself and will run you around $35.

May 31, 2011 | 2006 GMC Envoy

1 Answer

96 windstar looking for fuel pump relay, not by battery, looked all over need pin point directions where it is located, can't find ignigtion control module, i know where powertrain control relay module...


Check out your Inertia switch first. It is located in an access panel on the rear passenger side of your vehicle. There is a button to press to reset this and its function is to cut off power to the fuelpump in a wreck.

The fuelpump relay on your Year Windstar is suppose to be taped within the wiring harness going to the Starter. The Ignition control module and the PCM would affect the spark and since you have spark they have nothing to do with the fuekpump not working.

You can look in your Haynes book for the Inertia switch. The Starter Relay is Year model specific, for unknown reasons the Relay did not end up in a permanent position until later models. Would appreciate knowing if Inertia switch was at fault.

Nov 22, 2010 | 1999 Ford Windstar

2 Answers

1996 lincoln towncar. No a/c compressor engagement unless jumped


the control unit is no good.i had a similar situation with a 98 tracker,and installed a switch to give it a ground for the compressor relay that comes from the a/c computer module.
it works good and goes on and off with the a/c switch.

Jul 18, 2009 | Lincoln Town Car Cars & Trucks

1 Answer

1988 nissan sentra


Try following wires back from compressor to find relay if there is one.Try this link too, it may help you. check fig12

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801ce790

Dec 27, 2008 | 1988 Nissan Pulsar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

84625 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...