I replaced my remote batteries on 2006 dodge durango but after that the remote doesn’t work!! Do you know how can I reprogram it ?! Thanks

SOURCE: Reprograming a keyless remote

program transmitter code(s) as follows:
1) Confirm that all the doors are closed and the ignition key is out of the ignition cylinder.
2) Open the driver’s door. Insert the key and turn the ignition switch to ON position within 10 seconds.
3) Turn the ignition switch to OFF position within 10 seconds, remove ignition key from lock cylin-der.
4) Push and release the driver’s door switch (1) 3 times within 20 seconds.
5) Insert the ignition key and turn the ignition switch to ON position within 10 seconds.
6) Turn the ignition switch to OFF position within 10 seconds, remove ignition key from lock cylin-der.
7) Press and hold both LOCK and UNLOCK buttons (2) on the transmitter (3) for more than 5 seconds
within 20 seconds of removing the ignition key from the lock cylinder in step 6.
8) Press LOCK or UNLOCK button (2) on the transmitter (3) within 5 seconds (after step 7). All the
doors will lock/ unlock to confirm that this process has been properly done.
With this process, the transmitter has been programmed.
9) If you want to program an additional transmitter, repeat the procedure from Step 1) through Step 8).
10) Make sure that the keyless entry system properly operates by operating each transmitter.

SOURCE: keyless remote does not work after replacing batteries

I had the same problem and located the addendum to the owners manual. It's kind of overcomplicated it seems. Here is what it says:
1) Confirm all doors are closed and the key is out of the ignition.
2) Open the driver's door and put the key in the ignition within 10 seconds.
3) Remove the key within 10 seconds.
4) Push and release the driver's door switch 3 times within 20 seconds.
5) Insert the ingition key within 10 seconds.
6) remove the ignition key within 10 seconds
7) press and hold both "lock" and "unlock" on the transmitter for more than 5 seconds within 20 seconds of removing the key All doors will lock/unlock to confirm the process has been properly done.
8) Press "lock" or "unlock" on the transmitter within 5 seconds of completing step 7. All the doors will lock/unlock to confirm that the process was properly done.
At this point the transmitter has been properly programmed.

Of course, this didn't help me. My transmitter still does not work. I did confirm the procedure with a known good transmitter, so it is valid. If the lock/unlock does not happen in step 7, you more than likely have a bad transmitter.

SOURCE: keyless reprogram

resychronizing the key works.

1. Insert key into ignition and turn to
position 2.
2. Remove key and hold down lock button
while pushing unlock button five times.
3. Release all buttons, then push either lock or
unlock button.
!!!!!!!!!!!!!Procedure must be completed within10
seconds.!!!!!!!!!!!!!!!!!!!

SOURCE: Key remote stopped working

I HAD THE SAME PROBLEM, CHANGED OUT BATTERIES IN MY REMOTES AND HAD THEM TESTED AND THEY WORKED FINE. THEY DEALERSHIP STATED IT WAS NOT UNDER WARANTY AND IT WOULD COST $600 TO FIX IT. YOU CAN ONLY REPLACE IT THRU A CHEVY DEALERSHIP. KIND OF A SCAM!

Marvin

• 85242 Answers
• Posted on Jul 02, 2012

SOURCE: 08 dodge ram key FOB reprogramming

ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you.

Click here to find a Locksmith in your area to program this remote.
1. Enter your vehicle and close all doors.

2. Fasten your seat belt ( fastening the seat belt will cancel any chiming that may
confuse you during this programming procedure.)

3. Place key into the ignition.

4. Turn the ignition to the ON position ( DO NOT START THE ENGINE )

5. Press and hold the UNLOCK button on a working remote.

6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than
10 seconds, then press and hold PANIC button.

7. When a single chime is heard, release both buttons. The chime indicates the system
is in program mode.

8. Press and release both the LOCK and UNLOCK buttons, simultaneoulsly on the remote
to be programmed.

9. A single chime will be heard. The chime indicates the the remote was recognized.

10. Within 4 seconds of hearing the chime, press and release any button on the remote
being programmed.

11. A single chime will be heard The chime indicates the remote has been programmed.

12. Repeat steps 8 to 11 for a total of 4 remotes.

13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode.