How do I remove a windshield wiper motor from a 1994 jaguar xj6

wire burned up or corrosion, but sounds like wiring

The wiper motor on a Volkswagen is an electric motor connected through a drive linkage to the wiper arms. Windshield wipers are an integral feature for operating a motor vehicle safely. If your wipers are not functioning, or seem to lack the speed or power they used to have, the wiper motor should be removed and replaced immediately
.

Location

• The wiper motor on a Volkswagen is located directly underneath the plastic cowl cover. The cowl cover is located directly below the windshield.
  

Removal

• Begin by removing the wiper arms by prying off the covers at the base of the arms and removing the nuts that secure the arms to the drive shafts. Label the passenger and driver arms so they can be installed in the same positions. They are not interchangeable. Remove the rubber hood to cowl weather seal. Unscrew the plastic fasteners from the driver's side of the cowl cover, then remove this half of the cover. Remove the fasteners from the passenger's side cowl cover and remove this half of the cover. Disconnect the windshield wiper motor wiring harness by separating the plastic wiring connector. Remove the three bolts that secure the wiper motor to the vehicle's body. Pull the motor slightly away from the body, then remove the nut that connects the motor shaft to wiper linkage. Remove the motor.
  

Installation

• Place the new wiper motor into position in the cowl and reconnect it to the wiper arm linkage. Then reinstall the three retaining bolts. Reconnect the plastic wiring connector to the wiper motor wiring harness. Place the cowl covers into position below the windshield and reinstall the plastic fasteners that retain them. Reinstall the rubber hood to the cowl weather seal. Reinstall the wiper arms in the same position you removed them from, along with the wiper arm retaining nuts and lower wiper arm covers. Turn the windshield wipers on and test for proper operation. If the wiper blades slap against the bodywork surrounding the windshield, loosen the nuts that connect the wiper arms to the shafts and adjust.
  

More Read: OBD2 car diagnostic tool

Locate the wiper motor, and disconnect the electrical wires from it by unplugging them. The wiper motor is in the engine compartment against the back firewall near the driver's side.
Disconnect the wiper arms from the wiper motor linkage by using the pliers to remove the clip.
Locate the wiper motor in the engine compartment on the back firewall and remove it with the proper size wrench. There are three attaching bolts.
Remove the wiper motor by twisting it around if you have to. The wiper arm linkage will come out with it. good-day !

3Remove the cowl grill under the windshield wipers using the proper size screwdriver. This is the grill that you see under the wiper arms before the engine compartment hood starts.

Read more: How Do I Remove a Windshield Wiper Motor from a 1994 Ford F-250? ' eHow.com http://www.ehow.com/how_7195498_do-motor-1994-ford-f_250_.html#ixzz1odr1irhn

WINDSHIELD WASHER FLUID RESERVOIR
Part #: JLM12455 RESERVOIR, WINDSHIELD WASHER FLUID, FITS 1995-1997 XJ6. This is the large lower reservoir the top filler tube will need to be removed from your old reservoir ITS ABOUT 155.00

why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.

1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.

1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.

1. Remove left windshield wiper adapter and connecting arm clip access cover.

1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
   

----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal

1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.

1. Disconnect battery and wiper motor electrical connector.

1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .

1. Disconnect the battery ground cable (14301).

1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .

1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.

1. Reach through the access cover opening and unsnap the wiper motor clip.

1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.

1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.

1. Remove nut and ground strap.

1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .

Installation

1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).

1. Install nut and ground strap.

1. Connect wiper motor electrical connector.

1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.

1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.

1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.

1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
   

1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.

1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.

1. Test the system.

fisrt you have take off all attacment such as seat belt visor and and side panel attach to headliner the pull liner down and remove

Remove the windshield wiper motor for access to the top bolt. Use a 13mm dogbone with a pipe or similar for leverage.They used locktite on the bolts,so it's a bear to get loose. This job is a real P.I.T.A. Good luck.

There are two relays in the front of the air filter housing, by the driver head light. two are for the wipers, 1 is for turned on and off, and the other one is for fast or slow speed. but you will have to check your fuses first in the engine driver side bay. hope you can fix it

It more and likely is the servo motor (s) that are the problem, when you turn hot to cold and defrost they cycle the vents in conjuction and are a common failure on this model.
The ones that fail are accessible if you remove the right underscuttle panel and the glovebox.
Black motors with a double wire, usually have a red connector on the end.
JPTCAT

Many cars of that period could be reset by some ignition key sequence.
Try switching from the off position to the on (not start) several times within 15-30 seconds.
It won't hurt anything and might turn off the light.
If the problem is still present that caused the light to go on the first time, it will likely come on again after you start the engine.

I hope the reason for that alarm light has been since corrected.

Some cars needed to have the battery disconnected for several minutes to cancel the memory contents.
Newer cars will not likely respnd to that since flash memory is now common which retains the error code even without power.