1992 Plymouth Voyager Logo

Related Topics:

Robert Blannin Posted on Oct 22, 2018

1992 ply Voyager van ount shut off has new switch

5 Related Answers

Anonymous

  • 23 Answers
  • Posted on Aug 26, 2008

SOURCE: van wont start

check the small connector at starter for voltage when cranking if ok try the hammer test if starts bad starter (ie) tapping starter with hammer while trying to start.

Ad
motor1258

Mike Butler

  • 6674 Answers
  • Posted on Jul 12, 2009

SOURCE: speedometer on 1992 ply voyf gets erritic and van loses power o

Suspect vehicle speed sensor at transmission faulty. Cycling key to retrieve fault codes may confirm. Are you aware of how to do that?

Anonymous

  • 3 Answers
  • Posted on Jun 08, 2010

SOURCE: The ignition key will not trun in the switch, and

This is a common problem with these. Try hitting it (where you put the key in) with a hammer or some other piece of heavy metal. This resets the pins and the key should turn. I've had this problem before and now when it happens I just tap it hard with my finger or grab my tire iron and give it a few good taps. You could also go on ebay and buy another tumbler for around $50 if you want the headache of fixing it. I've just been dealing with it for almost a year now.

airjer995

Jeremy W.

  • 5332 Answers
  • Posted on Feb 16, 2012

SOURCE: diagram to install serpintine belt

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c15280215ae3

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Jeff Armer

  • 15575 Answers
  • Posted on Aug 07, 2018

SOURCE: I Have a 1992 Ply Voyager...Can you tell me what the #14 space in the fuse block is for..it is a 2amp fuse labeled speed control...what dose it do???

it's for cruise control switch on the steering wheel .

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

1992 ply Voyager new switch won't shut off Eng once started

Well if it worked fine before and now doesn't.. What changed? I'd look at a faulty new switch
0helpful
1answer

I have a 1992 ply voyager.it passed inspection,then the engine light stays on, now when i drive the van makes a loud jurking movement the stops and starts again. plse help.

You have an engine light on

So as with ALL Vehicle problems

You check for codes & resolve them first

Simply can't guess at vehicle problems without
a vehicle to drive & test
3helpful
1answer

90 ply voyager stalling not starting help replaced fuel pump gas tank lines relay full tune up

Reference voyager van wiggle test. If that did not solve your problem, you may have a cam sensor going bad. There is no way for you to check the computer. With a scan tool hooked to vehicle, can you read codes?
0helpful
2answers

Where is the ecm module located 92 ply voyager 3.3l

The 1992 Plymouth Truck Voyager 4WD 3.3L MFI 6cyl the Engine Control Computer is located under hood, driver side, front side of strut tower, rear of headlight, mounted on inner fenderwell .

Hope this helps (remember to rate this answer).
0helpful
1answer
2helpful
1answer

98 Ply Grand Voyager, 1.4K miles with recurring P0305 code.

You say you changed the cap and rotor so I'm assuming the van has a 3.0L? Possible injector problem on cylinder #5, swap injector with cylinder 1 or 3 and see if miss/dtc moves to that cylinder. You also could have a vaccum leak, although they usually won't come and go. Does the vehicle have a consistent miss or do you just have a check engine light?
0helpful
2answers

1992 plymouth grand voyager

yes, the engine gets hot and has a shut off to protect it from overheating to badly. Repair the fan and see if the problem is corrected. If not please let me know. Thanks
0helpful
1answer

1997 ply. van -van starts and runs as long as i hav my foot on accelerator --take foot off and car dies --??? allan

Check for dirty throttle body. Maybe IAC motor gummed up. If throttle body dirty, get some carb cleaner and a soft toothbrush and clean well. If this doesn't work, most likely an IAC (idle air control) motor.
0helpful
2answers

Van wont start

check the small connector at starter for voltage when cranking if ok try the hammer test if starts bad starter (ie) tapping starter with hammer while trying to start.
Not finding what you are looking for?

127 views

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...