Cars & Trucks Logo

Related Topics:

G
Garry Boneham Posted on Oct 22, 2018
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Where is the OBD connection in 2004 X Type Jaguar

1 Answer

Christian Samuelsen

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

  • Expert 81 Answers
  • Posted on Oct 22, 2018
Christian Samuelsen
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

Joined: Dec 22, 2008
Answers
81
Questions
2
Helped
37490
Points
110

5 Related Answers

Anonymous

  • 21 Answers
  • Posted on Dec 15, 2008

SOURCE: I am trying to locate

drivers side,bottom of dash on the outer edge if you imagine your foot on acc pedal it is located roughly above your shin,its the only plug there.if ya get a torch and have a look its a funny shaped plug.

Ad

Anonymous

  • 202 Answers
  • Posted on Apr 09, 2010

SOURCE: obd 2 codes P0302-P0304-P0305-P1313-P1316 and

THE P0302 is misfire cyclinder 2,4,and 5
The P1313 P1316 is Cyclinder compressor low, Worn camshaft/ broken valve springs. Fuel injector contamination, Spark plug failure/ incorrect gap. Iginition coil failure.
P0778 is 2/4 Brake prssure solenoid failure

HOPE THIS CAN HELP.

Anonymous

  • 56 Answers
  • Posted on Apr 24, 2010

SOURCE: Jaguar x type 2004 front bumper

Front bumper removal is quite easy. To start with there is 4 10mm bolts one by each headlamp ( with the bonnet open) remov them. There is 3 T30 screws that hold the under tray to the subframe and there is also a small corner trim that is on the bumper side of the front wheel arch here is 3 T30 screws holding them on on each side. Finally remove the front wheel arch lining so you can get acsess to the inside of the bumper. You will then see a 10mm bolt towards the top of the bumper that is reversed to you. Remove then the bumper should then just pull away.

Becareful not to damage the fog lamp harness upon removal

paul

  • 263 Answers
  • Posted on May 01, 2010

SOURCE: My clock in my Jaguar, 2004, S-Type has the wrong time?

FULLY PRESS THE BUTTON THAT SAYS MODE AND THE CLOCK WILL FLASH PUT 24HR AND TYPE IN THE TIME THEN PRESS MODE AND WILL RESET

Anonymous

  • 1 Answer
  • Posted on Apr 11, 2011

SOURCE: 2004 Jaguar X-type cigarette lighter fuse

2004 X Type 2.0L Diesel. Tried looking for fuse F68 in the glove box but can only see up to F55. Help please.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Replacing coil pack on jaguar s-type 4.0 engine

remove coil covers remove 8mm headed fixings run engine and lift coils one at time off the plugs slightly and listen! or easier get someone with a obd code reader but be carefull you get the right one has the cylinder numbering changed 2004 i think
0helpful
1answer
0helpful
1answer

My engine failure light has just come in my 2004 xtype estate what could the problem be?

The engine light came on because it is telling you that something is wrong somewhere with engine area so what you can do is take it to Advance Auto Parts store near you and have them check it out for free or you can buy the OBD II code sensor so you can test out the codes yourself. Without the OBD II codes that we would be guessing so you have to check it out with OBD II code reader.
1helpful
1answer

Wats the code p1000 on my 2002 jaguar x type

P1000 JAGUAR - On Board Diagnostic System Readiness Test Not Complete, this is known as the OBD2 drive cycle.


Possible causes - The vehicle is new from the factory.
- Battery or Powertrain Control Module (PCM) had recently been disconnected.
- An OBD monitor failure occurred before completion of an OBD drive cycle.
- PCM Detected Trouble Codes (DTC) have recently been cleared with a scan tool.
When is the code detected? If DTC P1000 is triggered after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles have not been cleared. P1000 JAGUAR Description The On Board Diagnostic (OBD) monitors are performed during the OBD Drive Cycle. P1000 is stored in continuous memory if any of the OBD monitors do not carry out their full diagnostic check.
5helpful
1answer

2003 jaguar s type what does p 1000 code mean

If the Dianosis test Code P1000 is flagged after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles HAVE NOT BEEN COMPLETED. See http://www.bluejag.co.uk for further details on this
0helpful
1answer

Check engine light(picture of motor)is on

This could be any one of hundreds of things, you need to either get your own OBD code reader or take it to a garage to get the fault code from the ECU
0helpful
1answer

S Type Jaguar rear bumper removal

how do you remove a front bumper off of an jaguar s type?
8helpful
1answer

Need to know what a p1000 diagnostic code means for a jaguar s ty

Looks like you have acommunication problem with the computer, it is going in to safe mode. Check all computer connections before you go to jaguar.
I have attached a picture of the error code.
hope this helps61f0008.jpg
Not finding what you are looking for?

153 views

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...