How do you seperate upper intake manifold from injector assembly

Yes you do, the following info explains the necessary procedure.



Click here to enlarge image.

Click here to enlarge image.

1. Properly relieve the fuel system pressure.
2. Disconnect the negative battery cable. Place a clean drain pan under the radiator, open the drain **** and drain the cooling system.
3. Remove the air cleaner assembly and the fuel injector sight shield.
4. Disconnect the cables from the throttle body and mount bracket.
5. Remove the coolant recovery reservoir.
6. Remove the inner fender electrical cover on the right side.
7. Remove the right rear crossover pipe heat shield.
8. Disconnect the fuel lines from the fuel rail and from the cable bracket.
9. Remove the alternator and brace.
10. Remove the throttle body cable mounting bracket with the vacuum lines and disconnect the vacuum lines.
11. Tag and detach the electrical connections at the throttle body and both banks of fuel injectors.
12. Disconnect the vacuum hoses from the canister purge solenoid valve and transaxle module and intake connection.
13. Unbolt the power steering pump and move forward. DO NOT disconnect the fluid lines.
14. Tag and disconnect the spark plug wires position lay aside.
15. Disconnect the coolant bypass hose from the intake manifold.
16. Remove the solenoid valve mounting bracket and power steering support brace from the intake manifold.
17. Disconnect the heater pipes from the intake and front cover.
18. Remove the alternator support brace from the intake.
19. Disconnect the upper radiator hose from the housing.
20. Remove the thermostat housing and thermostat from the intake.
21. Detach the electrical connector from the temperature sensor and sensor switch.
22. Unfasten the intake manifold bolts, then remove the manifold as an assembly. Remove and discard the gaskets.
23. If separating the upper manifold from the lower, proceed as follows:
24. Remove the fuel rail and fuel injectors.
25. Detach the coolant sensor switch.
26. Remove the manifold end cap cover.
27. Remove the upper intake manifold and throttle body assembly from the lower manifold. Remove and discard the gaskets. To install:
    
28. Thoroughly clean all gasket mating surfaces.
29. If replacing the upper manifold, proceed as follows:
30. Apply a 1⁄16 in. bead of Loctite® Instant Gasket Eliminator 51845 or equivalent to the lower manifold mating surface. Make sure to circle all bolt holes.
31. Carefully lower the upper manifold and throttle body assembly onto the lower manifold.
32. Tighten the upper manifold retaining bolts to 19 ft. lbs. (26 Nm).
33. Install the manifold end cap cover and the coolant sensor switch.
34. Install the fuel injectors and rail to the manifold assembly.
35. Clean the mating surfaces and install the intake manifold gaskets and seals. Apply sealer to the ends of the of the intake manifold seals.
36. Position the intake manifold and apply a suitable thread lock compound to the bolt threads. Tighten the retaining bolts to 88 inch lbs. (10 Nm), twice, in the sequence shown in the accompanying figure.
37. Attach the electrical connector to the temperature sensor and sensor switch.
38. Install the thermostat housing and thermostat with a new gasket.
39. Connect the alternator support brace to the intake.
40. Install the solenoid valve mounting bracket and power steering support brace to the intake manifold.
41. Connect the heater pipes to the intake and front cover.
42. Attach the coolant bypass hose to the intake manifold.
43. Install the power steering pump support bracket and tighten to 37 ft. lbs. (50 Nm).
44. Install the spark plug wires on both sides.
45. Install the belt tensioner pulley and tighten to 33 ft. lbs. (45 Nm).
46. Install the power steering pump.
47. Connect the vacuum hoses to the canister purge solenoid valve and transaxle module and intake connection.
48. Attach the electrical connections at the throttle body and both banks of fuel injectors.
49. Install the alternator and brace.
50. Connect the throttle body cable mounting bracket with the vacuum lines.
51. Install the right rear crossover pipe heat shield.
52. Install the cables to the throttle body.
53. Connect the fuel lines to the fuel rail and mount bracket.
54. Install the inner fender electrical cover on the right side.
55. Install the coolant recovery reservoir and upper radiator hose. Fill the cooling system.
56. Install the air cleaner assembly and the fuel injector sight shield.
57. Connect the negative battery cable.

The plenum shouldn't be damp with gas. Is it a throttle body fuel injection system?

Could be a leaky injector.

Fuel Meter Body & Fuel Injectors (4.3L Engine) Removal & Installation 1995-2002 Models (RPO L35) To Remove:
4.3L (RPO L35) Fuel meter body assembly

1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
2. Remove or disconnect the following:
   • Upper intake manifold (See: Upper Intake Manifold)
   • Fuel meter body
   • Injector retainer lock nuts (J) and retainer (K)
   NOTE: Use care in removing the fuel injectors to prevent damage to the electrical connector terminals. The fuel injector is serviced as a complete assembly only. Also since the injectors are electrical compartments, these injectors should not be immersed in any type of liquid solvent or cleaner as damage may occur. Fuel injector cleaning is not recommended.
   
3. While pulling the poppet nozzle tube downward, push with a small tip punch down between the injector terminals until the injector is removed

To Install:
4.3L (RPO L35) Fuel meter body assembly

Note: When ordering new fuel injectors, be sure to order the correct injector for the application being serviced.

1. Lubricate the new injector O-ring seals with clean engine oil.
2. Install or connect the following:
   • Fuel injector (L) into the fuel meter body injector socket
   • Retainer (K) and injector retainer lock nuts (J) and tighten the nuts
     1. Torque to: 27 inch lbs. (3 Nm)
   • Fuel meter body
   • Upper intake manifold (See: Upper Intake Manifold)
3. Test drive the vehicle to confirm the repairs.

1993-2005 Models (RPO LU3) To Remove:
4.3L (RPO LU3) Fuel meter body assembly

1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section.
2. Remove or disconnect the following:
   • Upper intake manifold (See: Upper Intake Manifold)
   • Fuel meter body
   • Injector retainer lock nuts (J) and retainer (K)
   NOTE: Use care in removing the fuel injectors to prevent damage to the electrical connector terminals. The fuel injector is serviced as a complete assembly only. Also since the injectors are electrical compartments, these injectors should not be immersed in any type of liquid solvent or cleaner as damage may occur. Fuel injector cleaning is not recommended.
   
3. While pulling the fuel injector downward, push with a small tip punch down between the injector terminals until the injector is removed

To Install:
Note: When ordering new fuel injectors, be sure to order the correct injector for the application being serviced.

1. Lubricate the NEW injector O-ring seals with clean engine oil
2. Install or connect the following:
   • Fuel injector (L) into the fuel meter body injector socket
   • Retainer (K) and the injector retainer lock nuts (J) and tighten the nuts
     1. Torque to: 27 inch lbs. (3 Nm)
   • Fuel meter body
   • Upper intake manifold (See: Upper Intake Manifold)
3. Test drive the vehicle to confirm the repairs

Here is the removal procedure, and the procedure is the same for both the V-6 and the V-8 Vortec engines. Also, be certain to put engine oil on the "o"-ring seal for the fuel injector assembly before installing the upper intake. Let me know if you require any further assistance.

REMOVAL:

1. Disconnect the battery negative cable assembly from the battery negative terminal.

2. Remove the air cleaner assembly.

3. Remove the wiring harness connectors and the brackets and move aside.

4. Remove the throttle cable and the bracket from the upper intake manifold.

5. Remove the cruise control cable, (if equipped).

6. Remove the fuel lines from the intake to the rear of the block.

7. Remove the ignition coil and the bracket.

8. Remove the upper intake manifold.

INSTALLATION:

1. Install the upper intake manifold gasket.

2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds.

3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves. NOTE: Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A "Play It Safe" final tightening sequence would be to tighten from the center most bolts to the outer most bolts.

4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.).

5. Install the purge solenoid and bracket.

6. Install the ignition coil and bracket.

7. Install the PCV hose et the upper intake manifold.

8. Install the fuel lines from the intake at the rear of the block.

9. Install the cruise control cable (if equipped).

10. Install the throttle cable and bracket from the upper intake manifold.

11. Install the wiring harness connectors and brackets.

12. Install the air cleaner assembly.

13. Connect the battery negative cable assembly to the battery negative terminal. - Tighten the bolt to 15 Nm (11 ft. lbs.).

Ha, you tried to fool me with the bit about a 3.5 L motor--I could find that one...here is the complete procedure from AutoZone.com:




Installation To install:

1. Clean the gasket mounting surfaces. Be sure to inspect the manifold for warpage and/or cracks. If necessary, replace it.
2. Position the gaskets on the cylinder head with the port blocking plates to the rear and the This Side Up stamps facing upward. Then apply a 3 / 16 in. (5mm) bead of RTV sealant on the front and rear of the engine block at the block-to-manifold mating surface. Extend the bead 1 / 2 in. (13mm) up each cylinder head to seal and retain the gaskets.
   
   Fig. Lower intake manifold tightening sequence-4.3L engines
   
3. Install the lower intake manifold. Tighten the bolts in sequence and in 3 steps, as follows:
   
   
   
   1. Step 1: 26 inch lbs. (3 Nm).
   2. Step 2: 106 inch lbs. (12 Nm).
   3. Step 3: 133 inch. lbs. (15 Nm).
   
   
4. Install or connect the following:
   
   Power steering pump Alternator bracket bolt near the thermostat housing Wiring harness to the lower manifold components, including the injector, EGR valve and ECT sensor Air conditioning compressor bracket-to-the lower intake manifold pencil braces
   
5. Install transmission oil dipstick tube, if necessary.
   
   Fuel supply and return lines to the rear of the lower intake
   
6. Temporarily reattach the negative battery cable, then pressurize the fuel system (by cycling the ignition without starting the engine) and check for leaks.
7. Disconnect the negative battery cable.
8. Install or connect the following:
   
   Heater hose to the lower intake Upper radiator hose to the thermostat housing Distributor assembly and engage the wiring Ignition coil Connect vacuum hoses to the upper and lower intake manifold. New upper intake manifold gasket, making sure the green sealing lines are facing upward Upper intake manifold Manifold retainers. Tighten them to 88 inch lbs. (10 Nm) using two passes. Purge solenoid and bracket Brake booster vacuum hose at the upper intake manifold PCV hose to the rear of the upper intake manifold Vacuum hoses to both the front and rear of the manifold assembly Throttle body Throttle linkage to the upper intake Wiring to the upper intake components including the TP sensor, IAC motor, MAP sensor and the fuel meter Engine cover Air intake assembly
   
9. Connect negative battery cable.
10. Refill the engine cooling system.
11. Start the engine and check for leaks.

3.3L & 3.8L Engines
Firing order: 1-2-3-4-5-6
Distributorless Ignition System
The Driver's Side Front spark plug is the #6 cylinder.

3.8L Engine (most common) Upper Intake Manifold To Remove:

1. Drain the cooling system.
2. Remove or disconnect the following:
   • Negative battery cable.
   • Fuel injector sight shield.
   • Air cleaner intake duct.
   • Right spark plug wires from the ignition control module and reposition.
3. Relieve the fuel pressure.
4. Remove or disconnect the following:
   • Fuel rail assembly.
   • Brake booster hose from the vacuum source manifold in the upper intake manifold.
   • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
   • Throttle body support bracket upper bolt.
5. Disconnect the electrical connectors from the following:
   • EVAP purge solenoid
   • Throttle Position (T/P) sensor
   • Idle Air Control (IAC) valve
   • Manifold Absolute Pressure (MAP) sensor
   • Mass Air Flow (MAF) sensor
   • EVAP purge solenoid vacuum line from the throttle body.
   • Accelerator and the cruise control cables with the bracket from the throttle body.
6. Remove or disconnect the following:
   • Upper intake manifold bolts and stud.
   • Clean the upper intake manifold bolt threads.
7. Remove or disconnect the following:
   • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
   • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
8. If the upper intake manifold is being replaced, remove the following:
   • Throttle body assembly.
   • Manifold Absolute Pressure (MAP) sensor.
   • Positive Crankcase Ventilation (PCV) valve.
   • Vacuum source manifold.

Upper intake manifold bolt torque sequence (3.8L engine)

To Install:

1. If the manifold was replaced, install or connect the following:
   • Vacuum source manifold.
   • Positive Crankcase Ventilation (PCV) valve.
   • Manifold Absolute Pressure (MAP) sensor.
   • Throttle body assembly.
   • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
   
3. Install or connect the following:
   • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
   • Accelerator and the cruise control cables with the bracket to the throttle body.
   • EVAP purge solenoid vacuum line to the throttle body.
4. Connect the electrical connectors to the following:
   • Mass Air Flow (MAF) sensor
   • Manifold Absolute Pressure (MAP) sensor
   • Idle Air Control (IAC) valve
   • Throttle Position (T/P) sensor
   • EVAP purge solenoid
5. Install or connect the following:
   • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
   • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
   • Brake booster hose to the vacuum source manifold.
   • Fuel rail assembly.
   • Right spark plug wires.
   • Air cleaner intake duct.
   • Fuel injector sight shield.
6. Connect the negative battery cable.
7. Fill the cooling system.
8. Inspect for fluid or vacuum leaks.

Lower Intake Manifold (W/O Supercharger) To Remove:

1. Remove or disconnect the following:
   • Upper intake manifold.
   • Generator brace.
   • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
   • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
   • Radiator inlet hose from the water outlet housing.
   • ECT sensor electrical connector.
   • Right upper engine mount strut bracket.
   • Generator brace bracket bolts.
   • Generator brace bracket.
   • Lower intake manifold bolts.
   • Lower intake manifold.
   • Lower intake manifold seals.
   • Lower intake manifold gaskets.
2. If replacing the lower intake manifold, Remove or disconnect:
   • Water outlet housing bolt and stud
   • Water outlet housing
   • Gasket and the thermostat.
   • ECT sensor.
3. Inspect the flatness of inlet flanges.
4. Clean the intake manifold mating surfaces.
5. Clean the intake manifold bolts and bolt holes of adhesive compound.

To Install:

1. If removed, install the ECT sensor.
   • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
2. If removed, install the thermostat, the gasket, and the water outlet housing.
3. If removed, install the water outlet housing bolt and the stud.
   • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
4. Install or connect the following:
   • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
     
   • Lower intake manifold seals.
   • Lower intake manifold.
   • Lower intake manifold bolts.
   NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
   
5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm)
   
   
6. Install or connect the following:
   • Generator brace bracket.
   • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
   • Right upper engine mount strut bracket.
   • ECT sensor electrical connector.
   • Radiator inlet hose to the water outlet housing.
   • EGR outlet pipe to the lower intake manifold.
   • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
   • Drive belt tensioner.
   • Generator brace.
   • Upper intake manifold.
7. Inspect for leaks.

Lower Intake Manifold (W/ Supercharger) To Remove:

1. Disconnect the negative battery cable.
2. Drain the cooling system.
3. Remove the supercharger.
4. Remove the thermostat housing.
5. Remove the EGR pipe at the intake manifold.
6. Disconnect the electrical connection at the temperature sensor.
7. Remove the intake manifold and gaskets.

NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:

1. Clean the gasket sealing surfaces.
2. Install the intake manifold gaskets.
3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
4. Install the electrical connector to the temperature sensor.
5. Install the EGR pipe to the intake manifold.
6. Install the thermostat housing.
7. Install the supercharger.
8. Fill the cooling system.
9. Connect the negative battery cable.

The Vortec engines were notorious for those kind of problems. The problem will be under the upper-intake manifold, and the fuel injector assembly will either have a cracked plastic fuel line running out to one or more of the fuel injectors, or the fuel pressure regulator that is located on the end of the fuel injector assembly is faulty or it has detached from the fuel injector assembly. Either way the lower intake manifold will be flooded with fuel anytime that the fuel pump runs.

There were two types made, the first type had fuel lines that connected to the lower intake manifold, and then from the metal fittings the fuel line turns into plastic and runs inside the lower intake manifold and under the upper-intake manifold where it runs over to the fuel injector assembly, and this type can really flood out an engine when it becomes faulty.

The second type had metal fuel lines running over the upper intake manifold and they connected to the top of the fuel injector assembly, however, under the upper-intake manifold there are still plastic lines to the fuel injectors and also the fuel pressure regulator that could be faulty and cause the engine to severely flood.

The upper-intake manifold is not that difficult to remove, and after you remove the upper-intake manifold then (replace the fuel lines to the fuel injector assembly if it is the second type) turn the ignition to the "Run" position and when the fuel pump runs you should see where the fuel is leaking/spraying from, and it will most likely be a large high pressure leak from a ruptured plastic fuel line.

Let me know if you require any further assistance.

These had a very common problem with the injector assembly inside the intake manifold. They develop leaks around the seals at the base of the injector spider. You can remove the plenum tuning device at the top of the manifold and look in with a flashlight and see how one side of the intake is washed and wet with fuel to confirm this. To fix the problem you'll need to buy a new injector assembly and gaskets for the upper intake assembly as it has to be removed to get at the injectors.

Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

3.8L Engine
VIN 1 Engine

1. Before servicing the vehicle, refer to the Precautions section.
2. Relieve the fuel system pressure.
3. Drain the cooling system.
4. Remove or disconnect the following:
   Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold

To install:

1. Install or connect the following:
   Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
2. Refill and bleed the cooling system.
3. Run the engine and check for leaks and proper engine operation.

VIN K Engine

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the negative battery cable.
3. Drain the cooling system.
4. Relieve the fuel system pressure.
5. Remove or disconnect the following:
   Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold
   
   
   Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
   

To install:



Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine



Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine

1. Install or connect the following:
   Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
2. Refill and bleed the cooling system.
3. Run the engine and check for leaks and proper engine operation.

Hope this help (remember rated this).

3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.

1. Disconnect the negative battery cable.
2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
3. Remove the upper intake manifold using the procedure above.
4. Remove the EGR outlet pipe from the intake manifold.
5. Detach the engine coolant temperature sensor wiring harness from the sensor.
6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine

1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)

1. Disconnect the negative battery cable.
2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
3. Tag for identification, then remove the right side spark plug wires.
4. Disconnect the ignition wires from the fuel rail.
5. Remove the fuel rail. Please see Section 5.
6. Remove the cable bracket from the intake manifold.
7. Remove the throttle body.

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.

1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.

Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:

1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
3. Install the remaining components in the reverse order of the removal process.