Same fuse as for the tail lights
Testimonial: "Hello Bill, Thanks for the info! Tim."
I just recently purchased a License plate light assembly for my Dad's 2006 Suzuki Grand Vitara, and had a mechanic put it in. When I turned on the lights, NOTHING! The tail lights are working, so what could be the problem? Wiring? Short circuit? I do not know where to turn. Please, if anybody can help me out there, I would appreciate it. Tim.
possible explanations
the power wire from the tail lights is not hooked up
the ground for the light is not connected
Hello Bill, where can I find the power wire for the tail lights, and where can I find the ground wire for the light. I thought when the mechanic put the assembly in, it would work. I only have a few days left to get my Dad's car inspected without having to pay another $18.50 for another inspection. This totally STINKS!
only $18.50 for an inspection
you can consider it stinks when you have to pay $120.00 for an inspection
run a wire from the light at the center of the holder to a power wire for a tail light
put the park lights on and use a multi meter to get which wire has 12 volts
use a buddy clamp to clip that wire from the light to that wire
now run another wire from the bulb holder case to any ground point
×
SOURCE: where is the starter for a 2000 suzuki grand vitara located
starters are normally located at the rear of the motor usually hard to get too or see. should be on your bell housing in other words just in front of the gearbox/clutch
SOURCE: cabin filter element location
Filter is located behind the glove box. All you need is a screwdriver to replace.
1. Open the glove box and empty to take the weight off the box.
2. On the right side there is a plastic hinge like device held on by one Phillips head screw. If you have trouble removing with a Phillips screwdriver you can remove with a narrow flat head screwdriver. Remove the screw and slide hinge off the mount.
3. To drop the glove box press the sides slightly inwards while 'forcing' it open beyond it's normal stopping point. Careful as when it releases it will fall wide open and may even fall from its hinged area. Set it aside.
4. Behind the glove box there is probably some fiberous material inserted to prevent noise like squeaking when it rubs. It is sticky on one side to hold it in place. Just remove and place out of the way.
5. Behind the fiberous material there'll be a cover which kinda looks like a grille. Mine was white and it is in the center of the opening. Remove it by releasing the clips at the left or right. It comes right out.
6. When the cover comes off slide the filter out and replace it. The filter lays flat and just slides in and out easily. However, if it has been some time since you replaced be prepared for a lot of debris on top of the filter such as leaves, grass or other general type of debris that has been sucked into the filter. It also may be the source of any bad odors that you smell through the air conditioning system.
7. Reverse the process. Replace the cover and push the glove box lid back into place. When you replace the glove box be careful to make sure the hinge you initiallly removed the screw from is not left behind the glove box or you will have to remove again to get it out. Replace the screw and do not over tighten as it screws into plastic and then your done.
SOURCE: where is the fuse box for Suzuki Grand Vitara.
Hi I'm litoshop there's one under the hood in the right side near the shock absorber tower and under the dash you find the relay block and some vitara have a fuse box in the lower left side behind the coin holder pull the coin holder and behind that you'll find a fuse box good luck if this information has been useful please let us know thank you.
SOURCE: Where is the fuse box located on a 2007 Suzuki
open the front cover
its locted at the right side close to the wing
its abalck or brown plastic cover you
need to open it in order to see the fuses
SOURCE: have to change clutch plate on suzuki grand vitara
If it's hard to get into gear you should check the clutch is disengaging properly.
Before changing the clutch plate, check that the clutch throw-out is adjusted correctly and the actuating hydraulics/levers have the correct amount of travel.
246 views
Usually answered in minutes!
×