Question about BMW Cars & Trucks

Open Question

Starter removal bmw e90 320i - 2006 BMW 3 Series

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ZJLimited
  • 17970 Answers

SOURCE: BMW 328i Starter how to replaice

1999 BMW 328I 2.8L EFI DOHC 6cyl

Starter - Removal & Installation

The starter motor on some models is very difficult to see from the top of engine compartment as it is covered by the intake manifold. On these models, without removing the intake manifold, the starter motor must be removed from underneath the vehicle. Because the starter motor mounting bolts are not easy to access, a long extension with a universal joint mounted on a proper sized socket could be used. A three foot transmission extension is commercially available from tool vendors that has a 3 / 8 inch drive of the driven end and 1 / 2 inch drive on the drive end. If used with a non-binding impact universal joint and a proper fitting impact socket, the starter motor fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the starter motor may have to be moved side-to-side several times to loosen the dowel pin if it has corroded in place.

NOTE When the battery is disconnected, the radio code, on-board computer and clock settings will be lost. The radio code should be obtained before disconnecting the battery or radio. Once the battery has been reconnected, the radio will not function unless the code is keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm) Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) E36 6-Cylinder Engines
Automatic Transmission Models

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Remove the climate control air intake duct at the rear of the engine compartment as follows:
    1. Release the grille clips at the rear and lift the grille upward from the rubber seal, then remove the seal.
    2. Remove the two self tapping Phillips screws from inside the duct to release the electrical harness housing.
    3. Press the electrical housing downward to expose and remove the two hex head self tapping screws on each side of the duct and lift the duct up and out of the engine compartment.
  5. Remove the intake manifold trim and valve cover trim covers.
  6. Disconnect the ignition coil electrical connectors and ground straps, label for reinstallation and place aside.
  7. Remove the two fasteners that secure the fuel injection electrical connector harness to the rail. Remove the harness and carefully place aside toward the back of the engine compartment behind the right side strut tower.
  8. Remove the intake manifold.
  9. Remove the electrical leads from the starter motor and place aside.
  10. Remove the starter motor mounting fasteners at the transmission bell housing, then remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket, then lift the starter motor upward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.
Manual Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Raise and safely support the vehicle.
  5. Remove the fasteners for the reinforcement mounted between the frame rails just behind the rear lower control arm bushing brackets. Mark the bar-s direction for proper reinstallation and remove the bar.
  6. Remove the fuel line cover located near the left side rear lower control arm bushing bracket.
  7. Release the fuel lines and reverse light wiring from their routing brackets.
  8. Note the routing of the starter motor electrical wires, remove the wire mounting nuts, and place the wires aside.
  9. Remove the top and bottom starter motor to engine-transmission mounting fasteners.
  10. Remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket and carefully lower the starter motor downward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.

Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor

cd45991.jpg

Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts

2cbfa11.jpg

I hope help you with this (rated this help) Good luck.

Posted on Sep 22, 2009

Ad
  • 1986 Answers

SOURCE: removal and replament of a 3 Series BMW E46 1998 saloon wing mirr

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

  • 510 Answers

SOURCE: replacing fuse for cd changer on bmw 3 series

If you turn radio on then mode it should display cd,if not there is no connection, either power or ubi cable.The only fuse is on the back of the changer.You have to remove to access.I don`t know your problem but if your cartridge will not eject, hold eject button and insert credit card under cartridge push fully in and move left to right this will locate micro switch.

Posted on Oct 28, 2009

  • 71 Answers

SOURCE: how can i remove door handle of bmw X-3

If you have the door panel off already. you have to look at the back of the door latch mechanism. you will see where the wire for the door handle hooks to the door. If you are starting you have to be very careful in removing the screws for the door panel look for the hidden screws under caps with cutout.there should be a toric screw where the door handle is and another one close to where the mirror mounts. again look for caps

Posted on Apr 26, 2010

  • 107 Answers

SOURCE: 2000 3 Series: where is the battery located on BMW 318i 2000...

in the boot on r/hand side.

Posted on Jul 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 bmw sunroof installation


BMW Sunroof Repair.wmv - YouTube

? 10:23
https://www.youtube.com/watch?v=TATFSv8CIsI
Jul 25, 2010 - Uploaded by 325xitgrocgetter
Repairing the Sunroof Shade on a 2003 BMW 325 xiT E46. Thisrepair will apply to all E46 models from ...

E46 3-Series BMW DIY Sunroof Repair - Up

www.lincomatic.com/e46sunroof/e46sunroof.html
One night, while driving my 2000 E46 3-Series BMW 323i, I tried to open my sunroof, and heard an omnious loud crunch; it sounded as if my sunroof had ...

E46 Sunroof ' eBay

www.ebay.com/bhp/e46-sunroof

eBay

Sunroof won't slide back, anyone know whatsup? - Bimmerfest - BMW ...

www.bimmerfest.com > ... > 3 Series / 4 Series > E46 (1999 - 2006)

May 25, 2013 - 15 posts - ‎8 authors
E46 (1999 - 2006) ... Mein Auto: 2003 BMW 325i ... about a week ago the sunroof quit sliding back, it tilts up even if i push the button back. DIY: BMW E39 Sunroof Repair (Video Tutorial)
8 posts
Nov 22, 2013
Sunroof won't close completely, expensive fix?
25 posts
Sep 26, 2010
Sunroof Shade Clip DIY
25 posts
Dec 28, 2005
Retrofit sunroof on E46 M3, is it wise?
13 posts
Mar 21, 2005
More results from www.bimmerfest.com

Dec 26, 2015 | BMW Cars & Trucks

1 Answer

2005 bmw x3 3.0l automatic. Swapped out starter from underneath. Removed drive line from frt of tr/case, removed t/cs crossmember.


BMW X3 Starter - PartsGeek.com

www.partsgeek.com > Starter > BMW Starter > X3 Parts
BMW X3 Replacement Starter Information. Read Reviews for ... Search our onlinestarter catalog and find the lowest priced discount auto parts on the web. We sell wholesale ... They are available for the following BMW X3 years: 2006, 2005, 2004, 06, 05, 04. This part is also ... 07 2007 BMW X3 Starter 3.0L 6 Cyl N52 Bosch.

Jul 25, 2015 | BMW Cars & Trucks

1 Answer

How much is a starter on bmw 325 ci 2006


The Bosch starter costs about $175, or $275 from the BMW dealer. This is generally not an easy job on the 3 series engine. You should estimate at least $400 in labor, maybe higher at the dealership.

Apr 13, 2013 | 2006 BMW 5 Series

2 Answers

My 2006 BMW 5 series fails to start. Lights and gauges come on, but not even a click when turn key. tried both keys. checked battery. 4 days later tried ignition and car operated normally, starting,...


If you can catch it failing again, test for power on the small wire going to the starter solenoid while someone tries to crank it. If you have no power, check for power at starter relay and trace backwards. If you have power, you have a bad starter. They can have intermittent failures. Hopefully your starter is easy to access, some 3 series and 5 series have the starter mounted under the intake manifold and it is necessary to removed the maifold to replace or test the starter. Good luck, hope this helps.

Oct 02, 2012 | 2006 BMW 5 Series

1 Answer

Remove starter on 2006 325i


it is located under the intake manifold.

Sep 03, 2012 | 2006 BMW 3 Series

1 Answer

Need a BMW 320d 2006 fuse box diagram


On this website you find fuse box diagram and description for BMW 3 Series (E90, E91, E92, E93) - 2005 - 2010

BMW 3 Series E90 E91 E92 E93 2005 2010 fuse box diagram

Sep 07, 2010 | 2006 BMW 3 Series

1 Answer

Replace bmw starter


disconnect neg end of battery, disconnect starter wiring then underneath car remove bolts and ease starter back a little and turn it till solenoide is at top and lower back of motor down and out.

May 30, 2010 | 1996 BMW 3 Series

1 Answer

Starter replacement


Removed top of motor, disconnected the hoses got to the starter, removed it without difficulty

Jan 15, 2009 | 1991 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

stephen Kiarie
stephen Kiarie

Level 1 Expert

32 Answers

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...