Head bolt torque specs and sequence for 2002 Nissan frontier so i can put it right please

Question edited for clarity.
Question moved to model category.

All here for the three engine types

https://www.autozone.com/diy/repair-guides/nissan-frontier-xterra-1998-05-torque-specifications-repair-guide-p-0996b43f8037fa5c

https://www.google.com/search?q=2004+Nissan+Xterra.+cylinder+head+bolt+sequence+and+torque+specs

..

AutoZone has a lot of info on torque specs for various vehicles.
The Xterra uses torque to yield bolts which must be replaced every time the bolt is removed.
Here's the site -
https://www.autozone.com/repairguides/Nissan-Frontier-Xterra-1998-05/Engine-Mechanical-Components/Cylinder-Head/_/P-0996b43f8037f9d4

You should have torque to yield bolts there. That means single use - you need to buy new bolts. Then, you would torque to spec (maybe 10-12 ft. lbs.) then an additional 65 degrees of tightening rotation.
Call your local auto parts supplier.
Repair Guides Specifications Torque Specifications AutoZone com

HERE'S A LINK TO THE HEAD BOLT SPECS. Repair Guides Engine Mechanical Components Cylinder Head AutoZone com SEE MY 85 NISSAN IN MY ICON.

Is there a diagram for head bolt sequence nissan frontier 2005 2.5 yd25 turbo diesel?

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

1. Step 1: 72 ft. lbs. (98 Nm).
   
2. Step 2: Completely loosen all bolts.
   
3. Step 3: 26-32 ft. lbs. (34-44 Nm).
   
4. Step 4: plus 90-95 degrees clockwise.
   
5. Step 5: plus 90-95 degrees clockwise.

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine




Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

According to Haynes Manual, 2005 Nissan Altima, using BRAND NEW cylinder head bolts:

1 - Tighten in sequence (as pictured) to 37 ft-lbs.
2 - Tighten an additional 60 degrees.
3 - Loosen all bolts completely.
4 - Tighten in sequence 26 - 32 ft-lbs.
5 - Tighten in sequence an additonal 75 degrees.
6 - Tighten in sequence an additional 75 degrees.

Hi there:



Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

1. Step 1: 72 ft. lbs. (98 Nm).
   
2. Step 2: Completely loosen all bolts.
   
3. Step 3: 26-32 ft. lbs. (34-44 Nm).
   
4. Step 4: plus 90-95 degrees clockwise.
   
5. Step 5: plus 90-95 degrees clockwise.

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine




Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!