At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
The top figure is for the 3.5L and the bottom figure is for the 3.0L galant engine.The top figure is for the 3.5L and the bottom figure is for the 3.0L galant engine.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
GENERAL/Standard Rules to Removal the Serpentine Belt with a Tensioner: A. Find the Tensioner(s). (See Diagrams on Link) B. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move. C. Remove the loosened belt off one of the other more easily accessed Pulleys. D. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.
Standard Rules for Installing the Serpentine Belt with Tensioners: a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on. b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right. c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley. d. Using your other hand - Pull the Belt up and over the Last remaining Pulley. e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
My apologies for the delayed response. I am going back to answer - unanswered questions. I have only been on this site for the past 4-months. Questions Posted have exploded (+55%) since joining. I do not know if you still need this information, but I am answering it either way.
To answer your Question: This all depends on the Options you have on your vehicle. Example Power Steering/No Power Steering; with AC/No AC, etc... Most of these do have a Tension Pulleys: meaning more than one tensioner.
CLICKon the following LINK. It has several Serpentine Belt Diagrams. Again based on your options will dictate what diagram applies to your vehicle, If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks!
VERY EASY, BACK UP THE TENSIONER AND REMOVE BELT. INSTALL THE SAME WAY YOU REMOVE IT, MAKE SURE YOU REMEMBER HOW IT GOES........ DRAW A PICTURE IF YOU NEED
My sincere apologies for the severely delayed response. I am going back to answer - unanswered questions. I have only been on this site for the past 4-months. Questions Posted have exploded (+55%) since joining.
CLICKon the following LINK. It has all the Diagrams for your Belt that you will need. If you would: Before Clicking let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com! Thanks!
×