Question about 2003 Saturn VUE

Open Question

My 2003 Saturn Vue 4 cylinder will not stay started

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ndguy2481
  • 251 Answers

SOURCE: what weight and type of oil to use for a 2005 Saturn Vue

5w30

Posted on Nov 28, 2008

Ad
badealer888
  • 414 Answers

SOURCE: 2003 saturn vue missfire

Test the coil pack that feeds those wires. Be sure it is mounted tight.Check ground wires and supply wires to the packs.

Posted on Jun 24, 2009

  • 1608 Answers

SOURCE: fuel filter location on a 2006 saturn vue 4

The fuel filter is in the primary fuel tank on your vehicle.

Posted on Dec 17, 2009

  • 39 Answers

SOURCE: 2003 saturn vue trouble code p1599

P1599 IS A STALLING ISSUE COULD BE BAD GAS / BAD FUELPUMP DIRTY FUEL FILTER
DISCONNECT BATTERY AND SEE IF THE LIGHT COMES ON AGAIN
U2107 HAS SOMETHING TO DO WITH THE COMPUTER LOOSING POWER AT THE BODY MOUNTS CHECK CABLES AND GROUND STRAP

Posted on Mar 02, 2010

techbuster
  • 5081 Answers

SOURCE: How do I remove the ignition lock cylinder from a

REMOVAL

  1. Disable SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".
  2. Disconnect negative battery cable.
  3. Remove lock cylinder bezel from steering column shroud by carefully prying with thin blade screwdriver.
  4. Remove shroud fasteners and remove steering column upper and lower shroud panels.
  5. Insert key into ignition lock cylinder and rotate to RUN position. Then rotate ignition cylinder back to ACC position.
  6. Depress locking button on side of ignition module assembly with a thin pick-type tool. Slide lock cylinder assembly from ignition module.
INSTALLATION

IMPORTANT: Actuator blade within ignition module housing must be in ACC position to install lock cylinder assembly. If rotated, replace it to ACC position, using needle nose pliers.

  1. Insert key into ignition lock cylinder and install into ignition module.
  2. Install steering column upper and lower shrouds and shroud fasteners.
  3. Install lock cylinder bezel.
  4. Connect negative battery cable.
  5. Enable the SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".

Posted on Apr 07, 2010

Testimonial: "Great information! Thanks for the help. Now I can get the ignition rekeyed to match the doors after the dealer changed the switch."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 03 saturn vue starts but does not go forward or reverse


Is this the 4 cylinder or the 6 cylinder model? The 4 cylinder has a notoriously troublesome Continuously Variable Transmission (CVT). These mischievous little skamps like to cause mischief at just the wrong times, such as when you are on your way to work on Monday morning, or when you are in the path of a train.

Since you have no engagement into forward or reverse the drive belt has likely failed you. Replace the case half and filter, and all of your dreams will be realized.... probably..

Feb 16, 2015 | 2003 Saturn VUE

3 Answers

2003 SATURN VUE SERIVE ENGINE SOON LIGHT IS BLINKING ON AND OFF RAN THE OBDII READER AND CODE P0304 CYLINDER MISFIRE CAME UP I CHANGE SPARK PLUGS AND BOOTS BUT CAR STILL DRIVES ROUGH SHAKES AND WHEN PARKED...


The P0304 indicates the #4 cylinder is misfiring. The flashing light means the cylinder is not firing at all...It could be several things causeing it, coil, wires, plug, injector or vacuum leak. Do not drive your vehicle until you have this repaired, as it will lead to further more costly problems. Good luck, i hope this helps.

Jul 27, 2011 | 2003 Saturn VUE

1 Answer

My service Light comes on and stay on after the car is on idle for 1 to 2 minutes. Is not on when you first start the car. I took it to a mechanic and he can;t find nothing wrong with the car, no computer...


If the light comes on then there is a code. the shop you went to may not have the updated software. try another shop. go to a parts store. they can read the codes.

Feb 07, 2011 | 2003 Saturn VUE

1 Answer

Where do you add tansmission fluid to a 2003 4 cylinder saturn vue


Remove the transmission dip stick and use a small funnel to add fluid. Be careful not to overfill. J.

Jul 04, 2010 | 2003 Saturn VUE

1 Answer

Does anybody know if or where the transmission dipstick is located at. 2003 saturn VUE 2.2L 4-cylinders


If you do not see it in the usual location between engine & transmission,out of the transmission, it is a sealed system. You need to go to a dealer or shop to have it checked. It has a special procedure to check & refill it.

Jun 13, 2010 | 2003 Saturn VUE

1 Answer

2003 saturn vue missfire


Test the coil pack that feeds those wires. Be sure it is mounted tight.Check ground wires and supply wires to the packs.

Jun 24, 2009 | 2003 Saturn VUE

1 Answer

Engine runs rough


soo many mechanical possibilities if you started a frozen motor..do you plug vehicle in with a water heater at night to keep it from freezing where you live?...you'll need to have a compression test to determine if a ring or valve train component didnt break from starting it when frozen..

Dec 08, 2008 | 2003 Saturn VUE

Not finding what you are looking for?
2003 Saturn VUE Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...