Question about Cars & Trucks

1 Answer

I need operating instructions for kal t143 tester

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,237 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda millennia s 4Dr sedan still runs hot put a brand new thermostat and waterpump any suggestions?


I would suggest doing a block test to ensure no head gasket or cracked block issue. You can rent a tester from Autozone or Orielly's. Make sure you buy the fluid to use in the tester. Follow the instructions that come with the tester.

Mar 16, 2016 | Mazda Cars & Trucks

1 Answer

Top got stuck when opening


Hi kal, I think that you might have to take it to a dealership. It's so easy to damage a tonneau if you don't really know how it works.

Jul 12, 2015 | Cars & Trucks

1 Answer

1994 4Runner-why does front Rgt tire wobble@50-70KL or wobble @thos speed when hitting a little bump or big bump&will not let me go past 70KL without starting to wobble??


Not Tie Rods, probably Upper and lower Ball joints OR look at the stabilizer bar if your truck has one, check for worn bushings on that.

Dec 04, 2012 | 1994 Toyota 4Runner

1 Answer

Need a manual for a KAL MD2204 meter


You may download a copy of the manual here.

Aug 26, 2012 | Cars & Trucks

1 Answer

Codigo


I'm sorry but I believe you have this posted in the wrong product category? Please re-post the question in the proper category if this is the case, otherwise you have my apologies. This is the car and truck problem category



Jul 08, 2012 | Cars & Trucks

1 Answer

Steeringproblem steering pulls to the right


Dear Kal,

If The Steering Pulls To One Side Or The Other It Could Be Because Of Tire Wear. Have The Front Tires Replaced And Aligned And Balanced. Most Of The Time Is Because You Need The Front Tires aligned. It Could also Be That If You Have Front Brake Pads. One Side Could Be Tighter Then The Other Side. Have Your Brakes Checked :o)

Hope This Helps,

Alex

Nov 13, 2011 | 1996 Buick Park Avenue

1 Answer

Hello, my BUICK LESABRE 2005 annual time to have tires rotated and brakes checked...so i did this....after they did this the AIRBAG LIGHT was on and wouldn't go off. called back KAL TIRE AND asked why...


Have a different shop put a scan tool on the car,
and look at the ABS Data

Then you will have a second opinon

Don't mention all the brake and tire work or
your questions about the what if's or what happened,
at the other tire place

Mar 16, 2011 | 2000 Buick LeSabre

1 Answer

Engine light came on and now it blinks off and on when its on solid car runs good but when it blinks car loses all its power wont hardly run and shakes


you need to hook up a diagnostic code retrieving tool to the aldl [ assembly line diagnostic link ] this is normally located on the drivers side under the instrument panel, it should be about 2 1/2 - 3 inches wide. the tester reteives the trouble codes that your car's computer has stored, you hook the tester up to the link, and turn your ignition key on, and the tester will start picking up the information that is stored in your computer, once it shows the code #s, write them down, and compare the # or #s to the diagnostic booklet that the tester comes with. [ follow the instructions of the tester] if you do not have a tester, your loacl auto part store can do this for you, normally free of charge.

Feb 20, 2011 | 2006 Lincoln Zephyr

1 Answer

1999 ford mustang cobra alternator troubleshooting


Generally, you can check and test alternator with this procedure...

1. Clean the positive and negative battery terminals to ensure a good connection with the tester's clamps.
2. Connect the positive and negative clamps to the appropriate battery terminals. The clamps must make firm contact with the battery terminals or the test results will be inaccurate or the tester may not work at all.
3. Turn the tester on and choose the option for "full charging system test." This will test your battery, starter and alternator and provide the most accurate picture of the problem.
4. Follow the directions on the tester's screen. These instructions will include cranking the vehicle after the battery test is performed, holding the engine at a certain RPM range and turning on certain accessories.
5. Read the results displayed on the tester's screen. The tester should scroll through the results, starting with the battery, then the starter and finally the alternator. An alternator test result showing diode ripple problems indicates a bad alternator.

Hope helps (remember rated this).
  • Step 2 Connect the positive and negative clamps to the appropriate battery terminals. The clamps must make firm contact with the battery terminals or the test results will be inaccurate or the tester may not work at all.
  • Step 3 Turn the tester on and choose the option for "full charging system test." This will test your battery, starter and alternator and provide the most accurate picture of the problem.
  • Step 4 Follow the directions on the tester's screen. These instructions will include cranking the vehicle after the battery test is performed, holding the engine at a certain RPM range and turning on certain accessories.
  • Step 5 Read the results displayed on the tester's screen. The tester should scroll through the results, starting with the battery, then the starter and finally the alternator. An alternator test result showing diode ripple problems indicates a bad alternator.

  • Read more: How to Test a Car's Alternator | eHow.com http://www.ehow.com/how_2079784_test-cars-alternator.html#ixzz0spTYveGJ

    Jul 05, 2010 | 1999 Ford Mustang Cobra

    2 Answers

    Searching for obd 2 port


    Hi!!

    The OBD Diagnostic Link Connector is located in front seating area, passenger side, under dash, above kick panel, mounted rear of glove compartment.

    Don't forget to rate this post, Good Luck!!

    Apr 27, 2010 | 1997 Ford Thunderbird LX

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    33 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    Marvin
    Marvin

    Level 3 Expert

    84625 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    john h

    Level 3 Expert

    20200 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...