Will a 2001 mustang ignition work in a 1998 - Mustang Ford Cars & Trucks

99 F-150 ignition/anti-theft question - Ford F150 Forum - FordF150.net

www.fordf150.net > ... > Electrical (Everything except audio systems)

Sep 16, 2009 - I had 2 keys for the truck, one worked perfectly fine, the other wouldunlock the ... over but the anti-theft light flashes and the engine won't actually start. ...Should I just spend the $80 for the switch and hope that is all it needs? ... for Fordkeys (Later 1998-newer Ford, Lincoln, Mercury) ... Mustang 1998 - 2001

electrical - Can I disable antitheft (PATS) on 03 Mustang ...

mechanics.stackexchange.com/questions/.../can-i-disable-antitheft-pats-o...

Jan 4, 2012 - So my question is: Is there a way to just disable the anti-theft system? ... This will make the car always 'see' a key with a chip. ... as they are usually intertwined with the anti-theft system to ensure the engine will not start. ... Where is the Wiper Relay/Control Module located on a 1994-1998 Ford Mustang??? 7.

How to Turn off Theft System on Cars: 7 Steps

www.wikihow.com > ... > Cars > Car Maintenance and Repair

wikiHowJump to Questions and Answers - Be the first to ask a question about this topic: ... Itwill not start and your battery will die. ... Reset a Check Engine Light ... Thanks to allauthors for creating a page that has been ... How to. Make Oat Flour. Cook Bacon in the Oven ... People are incredibly helpful and open to new ideas ...

if your car has a factory alarm it may be that you disabled the ignition , you need to have a professional do this kind of work as their is a code that needs to be entered into the computer , only a mechanic has the equipment do to it.

Have you checked for spark at the plugs and the fuel pressure ?
Can you hear the pump run for 3 seconds when you turn the key on ?

So I can use my 2001 Mustang 4.6 L that changed the ignition out and then I changed the computer out now that's flashing or it won't let it start and it starts to die

WHAT timing are you wanting to set? If you are trying to set the ignition timing, you are wasting your time because the ignition timing is not adjustable. If the ignition timing is incorrect, there is a mechanical malfunction that needs to be fixed.

Give some more details of the problem.

are you using a copy of the original key

you need to use the original key for the car

Antitheft and Alarm Systems: Description and Operation
ANTI-THEFT
The passive anti-theft system (PATS) uses radio frequency identification technology
to deter a driveaway theft. Passive means that it does not require any activity from
the user.
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a
permanently installed electronic device called a transponder. Each transponder
contains a unique electronic identification code, with over 72 million billion
combinations.
Each encoded ignition key must be programmed into the vehicle powertrain control
module (PCM) before it can be used to start the engine. There are special diagnostic
procedures that must be carried out if new encoded ignition keys are to be
configured.
The encoded key is larger than a traditional ignition key. The key does not require
batteries and should last the life of the vehicle.
The transceiver module communicates with the encoded ignition key. This module is
located behind the steering column shroud and contains an antenna connected to a
small electronic module. During each vehicle start sequence, the transceiver module
reads the encoded ignition key identification code and sends the data to the PCM.
The control functions are contained in the PCM. This module carries out all of the
PATS functions such as receiving the identification code from the encoded ignition
key and controlling engine enable. The PCM initiates the key interrogation sequence
when the vehicle ignition switch is turned to ON or START.
The PATS function uses the PCM to enable or disable the engine. All elements of PATS
must be functional before the engine is allowed to start. If any of the components
are not working correctly, the vehicle will not start.
PATS uses a visual theft indicator located on top of the instrument panel. This
indicator will prove out for three seconds when the ignition switch is turned to ON
or START under normal operation. If there is a PATS problem, this indicator will
either flash rapidly or glow steadily (for more than three seconds) when the ignition
switch is turned to ON or START. PATS also "flashes" the theft indicator every two
seconds at ignition OFF to act as a visual theft deterrent.
The PATS is not compatible with aftermarket remote start systems, which allow the
vehicle to be started from outside the vehicle. These systems may reduce the vehicle
security level, and also may cause no-start issues. Remote start systems must be
removed before investigation of PATS-related no-start issues.

The PATs key is used on the following Ford family trucks and suvs:

FORD: 1996-2001 MUSTANG, TAURUS
1998-2000 CONTOUR
1998-2001 CROWN VICTORIA
2000-2001 FOCUS
2002 THUNDERBIRD
1997-2001 EXPEDITION
1998-2002 EXPLORER
1999 F-250 LD
1999-2001 F-150, RANGER, WINDSTAR
2000-2001 EXCURSION
2001 ESCAPE
LINCOLN: 1997-1998 MARK VIII
1998-2001 CONTINENTAL, TOWN CAR
2000-2001 LS
1998-2001 NAVIGATOR
2002 BLACKWOOD
MERCURY: 1996-2001 SABLE
1998-2000 MYSTIQUE
1998-2001 GRAND MARQUIS
1999-2001 COUGAR
1998-2002 MOUNTAINEER

Additionally, PATs can be found on the follow Ford family cars and mini-vans:

1998-up Contour
1997-up Crown Victoria
1999-up Escort
2000-up Focus
1996-up Mustang and Taurus
1998-up Windstar
1998-up 2000-up Lincoln LS
1998-up Lincoln Mark VIII, Lincoln Continental and Lincoln Town Car
1997-up Mercury Grand Marquis
1998-up Mercury Mystique
1996-up Mercury Sable

Following are the instructions for programming a blank key (you must have at least one working key for this procedure).

The PAT

1. Make sure you have both keys.
2. Turn on car but don't start. Watch "theft" indicator untils it goes out.
3. Turn off and repeat procedure with second key.
4. After "theft light goes out, insert new key and turn on.
5. Wait until the theft indicator goes off and then turn off switch.
6. Wait thirty seconds. New key is now programmed into security module. Repeat for any other keys.


1. Erase any old codes by entering the factory code.(buttons will light up)
2. Press 1/2 button within 5 seconds.
3. Press 7/8 and 9/0 buttons at the same time within 5 seconds.

To set new code:

1. Enter factory code (numbers will light up)
2. Press 1/2 button within 5 seconds.
3. Enter personal 5 digit code(decide beforehand) within 5 seconds of each previous one.
To unlock all the doors,press the 3/4 button within 5 seconds of the driver door unlocking.
To lock all doors and set alarm system,press 7/8 and 9/0 at the same time.
To disarm or reset a triggered alarm,just enter personal or factory code.

Do not set a code with five of the same consecutive numbers. It's too easy for thieves to figure out.

Deactivating and Activating Autolock

To deactivate the "autolock":
With all doors and tailgate closed but NOT locked,and ignition OFF.
1. Enter 5 digit code
2. While holding 7/8 button in, press and release the 3/4 button.
3. Release 7/8 button
The horn will chirp once if the "autolock" was deactivated
or two times if "autolock" was activated.

To reactivate the system,repeat steps 1 thru 3

Alternate Method To Deactivate And Activate Autolock

Do steps [1] through [5] (below) within 30 seconds or you'll have to do it over. If you have to do it over, wait 30 seconds between attempts.
Close all doors securely.

1.Turn the ignition key to ON.

2.Press the power door UNLOCK control THREE times.

3.Turn the ignition key from ON to OFF.

4.Press the power door UNLOCK control THREE times.

5.Turn the ignition key back to ON .The doors should lock and unlock.

6.Press the power door UNLOCK control. The horn should chirp ONCE to confirm successful switching of the autolock system

Troubleshooting:

The engine does not start and LED remains off.
1. Check PATS system fuses
2. If alarm is fitted check if LED functions for alarm: if not check cigar lighter fuse (also used for LED)
3. If not go to main dealer

Engine does not start: LED flashes rapidly Leave ignition on until the LED starts to flash a 2 digit code: (sequence- pause-sequence)
Check the following codes:
Code flashes:
1:3 Key code not received. Is key screened by other keys or objects? Try different key: if okay then first key is faulty. If not go to main dealer
1:4 Partial code only received. Try again. If not okay use different key. If not go to main dealer
1:5 Key not programmed into PATS. Program key as above using master
1:6 Faulty link between PATS module and EECV Go to dealer .

Go to this free Ford website and download the owners manual for your vechicle. It shows the fuse boxes and the location and size of all the fuses.

https://www.fleet.ford.com/maintenance/owners_manuals/results.asp

it's the ignition switch 2 fuse

I would suspect the starter solenoid has failed.

A starter solenoid (or starter relay) is the part of an automobile which relays a large electric current to the starter motor, which in turn sets the engine in motion. In many vehicles the solenoid also engages the starter pinion with the ring gear of the engine.

The starter solenoid receives a large electric current from the car battery and a small electric current from the ignition switch. When the ignition switch is turned on, a small electric current is sent to the starter solenoid. This causes the starter solenoid to close a pair of heavy contacts, thus relaying a large electric current to the starter motor, which in turn sets the engine in motion. The starter motor is an electric motor that initiates piston motion in a car's internal combustion engine before it can power itself.