Exact location CKP sensor 2014 2.0 patriot - Patriot Jeep Cars & Trucks

In the link

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk03y9u8WcYEwtQjRdPkxhax5XeOPqw%3A1614804740010&ei=A_c_YN_3PNGw5NoPi7-E-AU&q=+jeep+patriot+2009+4wd+sensor+speed+location

..

Your vehicle's crankshaft position sensor, commonly abbreviated and referred to as a CPS sensor, CKP sensor, or CAS (crank angle sensor), is a key component to your engine control system. It is typically located on the front of the engine on the timing cover. The crank sensor uses a pickup (usually a Hall effect sensor) to determine the position of the crankshaft and sends the info to the vehicle's computer. The computer uses this information from the crankshaft sensor to control engine parameters such as ignition timing. This sensor can also be sometimes referred to as an "engine speed sensor (ESS)" or a "rotational speed (RPM) sensor" as well.

The CKP sensor is MOPAR# 5149167AE, It is located on the passenger side of the engine, halfway up between the bell housing flange and the engine oil dip stick tube.

easter egg hunts again.
2.4L
The MAP sensor mounts to the intake manifold.

http://www.chryslercommercialvehicles.com/jeep/download/pdf/manuals/2014-Patriot-OM-1st.pdf http://www.chryslercommercialvehicles.com/jeep/download/pdf/manuals/2014-Patriot-OM-1st.pdf

code p0017 refers to crank/ cam oosition sensor bank 1 sensor B -correlation ===causes --wiring--CKP sensor--CMP sensor--mechanical fault.
It also refers to control modules, cooling fan--no signal===causes -- wiring--ECM.
If it has a timing chain then the the advice that it will not be the chain is good. So I suggest checking out the cam/ crank sensors and wiring

The Crankshaft Position sensor is by the Oil Filter, or right above the oil filter. Here is a picture:



Here is a picture of the CKP Sensor:


I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

REMOVAL & INSTALLATION -

1. Disconnect the wiring harness from the Crankshaft Position (CKP) sensor.
2. Remove the fastening bolt for the CKP sensor.
3. Remove the CKP sensor and the O-ring seal from the engine block. To install:
   
4. Thoroughly clean the mating surfaces of the CKP sensor and the engine bock.
5. Install the CKP sensor with a new O-ring seal, into the engine block.
6. Install he fastening bolt for the CKP sensor
7. Attach the wiring harness to the CKP sensor. Be sure to route the cable correctly Fig. 1: The location of the Crankshaft Position Sensor (CKP) - 3.0L engine
   Fig. 2: Location of the CKP sensor connector - 3.0L engine
   

Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Jeep Patriot Crankshaft Position Sensor replacement ...

? 9:09
https://www.youtube.com/watch?v=omwDHaBGUEc
Jan 15, 2012 - Uploaded by JasonthePCMD
Here's how to replace the Crankshaft Position Sensor (CKP) on a 2008 and newer Jeep Patriot, Compass ...

Jeep Cherokee camshaft crankshaft sensor how to replace ...

? 2:59
https://www.youtube.com/watch?v=oOc1Lxod2x8
May 17, 2012 - Uploaded by unpescad0
How to locate and install a new camshaft and or a crankshaft position sensor. This vehicle is a 2001 Jeep ...

Crankshaft position sensor location - Jeep Patrio