Cars & Trucks Logo

Related Topics:

sixfricks
sixfricks Posted on Mar 27, 2018
Be the first to answer

My left front window will not go up on 2010 expedition. I was going to replace the regulator, but I cant get the window up.

Answer This Question

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Aug 25, 2008

SOURCE: Front window regulator

Remove inside panel, start by removing electric switchs from panel, and disconecting the female end. Inside panel can be removed by pulling tabs, a screw driver will do. You must then loosen bolts on window slide to free window. adjust regulator tab to approprate height to shut window, then assemble reverse directions.

Ad

Anonymous

  • 65 Answers
  • Posted on May 17, 2009

SOURCE: I need to change out a broken window regulator on the left side front door

replacing the window regulator is pretty simple there is no need to go to a maual window all u have to do is take the door panel off and if u will go by the window regulator u can identify whick part u will need to remove and replace its a bolt on item and fairly simple to replace but the part is kinda pricey around 200-300 bucks but if u go to ebay u can buy one for around 80 -100 bucks good luck

Anonymous

  • 1 Answer
  • Posted on Jul 01, 2009

SOURCE: replace left front window regulator

Link to replace the window motor and regulator.

http://wiki.answers.com/Q/How_to_replace_window_motor_for_a1999_sienna

-Viz

Anonymous

  • 1986 Answers
  • Posted on Aug 14, 2009

SOURCE: 4 door sedan left front window regulator manual

You'll need to remove screws that are by the door handle, arm rest, under door and side of door. Slide the retaining clip on the window crank to the side and the crank will pop off. Then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. Then pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything.You'll need to disconnect the bolts holding the regulator to the frame and connecting the regulator to the base of the window (make sure you use wedges to hold the window up) and the regulator will slide out of the door.. reverse to put back

simidrm45844

  • 159 Answers
  • Posted on Sep 27, 2009

SOURCE: Replacement Front, Driver Side Window Regulator

first these are easy to do,second look on ebay a-1 auto I think sells replacement for around $100 U.S
Take door panel off,there are several bolts in reg and 2 keepers on the window glass unhook the 2 keepers unplug the motor and turn unit and bring out the bottom of the doorthe window glass does NOT have to come out. it should only take less than an hour to do.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

I have a 2000 chevy s10 2wd. Where is the relay switch to my drivers side window. The window switch is and the motor is good. But cant find the relay switch to check it and see if it's bad.
Sorry but there is no relay switch ! Go to www.bbbind.com free wiring diagrams .Check it out ! Your regulator is probably bad ! Is there B+ voltage at the switch , at the motor ?
Left Front Window Switch Operation
Place the ignition switch in the RUN position in order to supply battery voltage to the left front door lock and side window switch through the POWER WINDOW circuit breaker and the CKT 1001 (DK GRN). Press the left front window UP switch in order to supply battery voltage to the left front side window regulator motor through CKT 164 (DK BLU). The window motor is grounded through CKT 165 (BRN) and the window switch DOWN contact.
The regulator motor runs to drive the window to the UP position. Press the DOWN window switch in order to provide battery voltage to the window regulator motor in the opposite direction through CKT 165 (BRN). The window regulator motor is grounded through the CKT 164 (DK BLU) and the window switch UP contact. The motor runs in order to drive the window down.
Read full answer
Aug 22, 2016 • Cars & Trucks
0helpful
1answer

97 ford expeditions front power windows do not go down when vehical is running. They sometimes will work if you push the back window up button and the front windoe down button at the same time. They also...
Sounds like window regulator switch is bad or contacts need cleaned. If they are intermittent then it is likely a wiring or switch contact issue
Read full answer
Sep 24, 2013 • 1997 Ford Expedition
2helpful
1answer

Window cable broke so window does not go up and down
The window regulator cable on a Ford Expedition is part of the regulator assembly and is not serviceable separately. Therefore, if your Expedition's window regulator cable incurs damage, you'll need to replace the entire regulator. The cable moves the regulator up or down in response to the window motor. If the cable malfunctions, you won't have command of your Expedition's power window until you replace the regulator. If you have basic auto-repair skills and an hour of free time, you can replace your Expedition's window regulator. Pry the window switch bezel out of the Expedition's door panel using your trim tool. Disconnect the switch from the door harness by hand and set the switch/bezel assembly aside.

  • 2 Remove the hex head screws from the door panel using the Phillips screwdriver. Depending on the year of your Expedition, you may need to remove a trim cover from behind the inner door handle with the trim tool to expose that screw.
  • 3 Lift the door panel up and off the door by hand. If your Expedition has a courtesy light in the lower-trailing edge of the panel, disconnect that light from the door wiring harness before moving the panel away from the door.
  • 4 Push the Expedition's window to the top of the window frame by hand. Tape the glass to the top of the door with packing tape to prevent it from dropping back down.
  • 5 Remove the window regulator mounting bolts with the socket set. Unbolt the regulator from the window glass with the socket set. Pull the old regulator out of the Expedition's door by hand.
  • 6 Set the new window regulator into the Expedition's door by hand. Bolt it in place with the socket set.
  • 7 Reinstall the Expedition's door panel in reverse of how you removed it.
    • Read full answer
    Oct 17, 2011 • 1997 Dodge Caravan
    3helpful
    2answers

    Power window will not roll up on 2004 expedition
    window has become loose from regulator and jammed or regulator has failed or switch has failed. if you hear the lift motor spinning when you hit the switch you can rule out the switch. if the window simply fell down and won't come up i would think it is disconnected from the regulator. if the window was going up and down problematically for a few days prior to failing i would suspect the regulator. you can buy a regulator new on ebay and have a glass shop install it much more cheaply than a dealer.
    Read full answer
    Sep 18, 2010 • 2004 Ford Expedition
    0helpful
    1answer

    2003 Expedition, cable broke on front power window. Are these replaceable? If not is this a do it your self repair or allow a dealer to fix.
    They are replaceable although you must replace the entire window regulator. You may find some good deals online, and its a fairly easy job. Hopefully this helps!!
    Read full answer
    Mar 28, 2010 • 2008 Ford Expedition
    3helpful
    1answer

    Diagram on how to take off left door panel on 1998 ford expedition
    REMOVAL AND INSTALLATION Trim Panel —Front Door, Expedition Removal
    1. NOTE: Release the top portion first.
      Remove the sail panel.
    cff7e48.gif
    1. Remove the window regulator switch plate (14524). 3745193.gif

    1. Disconnect the electrical connectors.
    d860af8.gif
    1. Remove the upper door trim panel screw. 4b4377b.gif

    1. Remove the door trim panel screw at the window regulator switch plate opening. 149d0a6.gif
    1. Remove the door trim panel screw in the courtesy lamp housing.
      1. Remove the courtesy lamp lens.
      1. Remove the screw. 8fe707b.gif

    1. Remove the inside door handle trim cover. 52f3d0f.gif
    1. Remove the inside door handle.
      • Remove the bolt. abe462f.gif
    1. swj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the front door trim panel, do not pull directly outward.
      Lift upward and then outward to remove the front door trim panel (23943). d6459fb.gif
    1. Remove the courtesy lamp and socket. dfb380f.gif
    1. Disconnect the power mirror electrical connector.
    Installation
    1. Connect the power mirror electrical connector.
    1. Install the courtesy lamp and socket.
    1. Install the front door trim panel.
    1. Install the inside door handle.
      • Install the bolt.
    1. Install the inside door handle trim cover.
    1. Install the door trim panel screw in the courtesy lamp housing.
      1. Install the screw.
      1. Install the courtesy lamp lens.
    1. Install the door trim panel screw at the window regulator switch plate opening.
    1. Install the upper door trim panel screw.
    1. Connect the electrical connectors.
    1. NOTE: If a new trim panel is required: Some new trim panels have a cut out opening for the window switchplate that is larger than that on the original trim panel. When installing a new trim panel, install the window switchplate in the following sequence to make sure that the switchplate is secured fully into the door trim panel.
      Install the window regulator switchplate.
      • Insert the rear switchplate clip into the trim panel opening.
      • Install the forward and side clips into the trim panel opening.
    1. NOTE: Install the lower portion first.
      Install the sail panel.
    Read full answer
    Mar 14, 2010 • 1998 Ford Expedition
    0helpful
    1answer

    Window fell down in door
    window regulaotr cable broke. Need ane regulator. go to tascafordparts.com for discount price. Do not use a used one.

    Front Door Window Regulator Motor Removal and Installation
    1. Raise the front door window glass to the full up position.
    1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
    1. Remove the door speaker.
    1. Position the watershield aside.
    1. sxj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the electrical connector is positioned aside before drilling.
      To access the power window motor bolts, use a 19 mm (3/4-in) hole saw with a 8 mm (1/4-in) pilot to drill three holes at the existing drill dimples on the door.
    cc3b152.gif
    1. Disconnect the front door window regulator electrical connector.
    1. Remove the bolts and the front door window regulator motor.
    Read full answer
    Jul 02, 2009 • 1999 Ford Expedition
    1helpful
    3answers

    Instructions on how to install window regulator on 99 Expedition
    Answer
    Here is the procedure, the "dimples" are on the metal surface of the inside of the door. With the waterscreen off you can locate the motor to help you tell where the dimples are. Drill holes then use a socket to remove window motor bolts.

    Front Door Window Regulator Motor
    Removal and Installation

    Raise the front door window glass to the full up position.
    Remove the front door trim panel.
    Remove the door speaker.
    Position the watershield aside.
    CAUTION: Make sure the electrical connector is positioned aside before drilling.

    To access the power window motor bolts, use a 19 mm (3/4-in) hole saw with a 8 mm (1/4-in) pilot to drill three holes at the existing drill dimples on the door.

    Disconnect the front door window regulator electrical connector.

    Remove the bolts and the front door window regulator motor.

    To install, reverse the removal procedure.
    Cycle the window glass to make sure the gears engage
    Read full answer
    Jun 22, 2009 • 1999 Ford Expedition
    3helpful
    1answer

    How to replace window regulator
    you will need to drill out some rivets. Replace with ntus and bolts and washers & lock washers. Make sure they don't hit glass going up and down. Otherwise you will need a heavy duty riveter.
    please rate as fixya if this helps.

    Motor —Front Door
    Special Tool(s) swj~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
    501-D011 (D80L-23200-A) or equivalent
    Removal
    NOTE: The window regulator and motor are removed as an assembly.
    1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
    1. Remove the front door radio speaker.
    1. Remove the latch remote control. For additional information, refer to Section 501-14A .
    1. Remove the front door watershield.
    1. swj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the window glass to avoid damage.
      Raise and support the front door window glass to the full up position.
    1. Disconnect the power window motor electrical connector.
    1. Remove the window glass to regulator nuts.
    1. Remove the motor and window regulator assembly.
      1. Drill out the rivets.
      1. Remove the motor and window regulator assembly.
    88565ca.gif
    1. NOTE: Prior to motor removal, make sure the regulator arms are in a fixed position to prevent counterbalance spring unwind.
      Remove the power window motor.
      1. Remove the bolts.
      1. Remove the power window motor.
    Read full answer
    Mar 21, 2009 • 1998 Ford Expedition
    0helpful
    1answer

    The power window on my truck will come down, but won't go back up. The motor seems to be working fine. I need a diagram of all the parts so I can determine which parts need to be repaired or replaced....
    The power window regulator and motor come as am assembly. Usually the cable snaps and the window drops down and won't come back up. About a $400 repair.
    ------------------------------------------------------------------------------------------

    1. Remove the front window regulator.
      • Loosen the two hanger bolts.
      • Remove the front window regulator bolts and front top run channel bolt.
    bb64879.gif
    Read full answer
    Feb 17, 2009 • 2004 Ford Expedition
    Not finding what you are looking for?

    View Most Popular

    Cars & Trucks

    Related Question

    I have a 2000 chevy s10 2wd. Where is the relay switch to my drivers side window. The window switch is and the motor is good. But cant find the relay switch to check it and see if it's bad.

    • Cars & Trucks

    81 views

    Ask a Question

    Usually answered in minutes!

    Popular Questions

    Need firing order diagram for a 5.4 ford

    2003 Ford Expedition

    I keep getting the codes p2196 and p2198

    2004 Ford Expedition

    2003 Ford Expedition fuse box

    Ford Expedition Cars & Trucks

    2005 expedition fuse box diagram

    2005 Ford Expedition

    Electronic Throttle control light came on and car died

    2005 Ford Expedition

    Check Out the Latest Top Trucks Report!
    Check Out the Latest Top Trucks Report!

    View all Fixya Reports

    Top Ford Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    xxxxxx xxx

    Level 3 Expert

    5117 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    PDF Manual
    98navog1e.pdf. user-manual-1998...

    1998 Ford Expedition

    PDF Manual
    98navog1e.pdf. user-manual-1998...

    1998 Ford Expedition

    PDF Manual
    98navog1e.pdf. user-manual-1998...

    1998 Ford Expedition

    Loading...