Question about 1995 GMC Sierra C1500

3 Answers

1995 GMC Sierra Z71 ABS light stays on

Replaced front brakes & ABS light stays on - Took to repair shop & ran codes....No codes for ABS

Posted by on

  • 1 more comment 
  • kim1315 Jul 31, 2009

    gonna disconnect battery tonight...& check that the sensor is plugged in. (Do you mean in the wheels or under the driver door?)

  • kim1315 Jul 31, 2009

    left battery cables off the whole night....light is still on

  • joseriver212 May 11, 2010

    thinks its the same thing......95 silverado 4.3 4l60e when it turns on no abs light and everything shifts right.....after driving it for a few mins, abs light turns on,won't shift anymore, and speedometer goes crazy.......thought it was the speed sensor replaced it but no luck



3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yo man, idk if this is exactly what your problem is but my 1991 gmc sierra was doing the same fuckin thing and ****, and i took it to the gm dealer and had them look at it and my connectors and my ignition switchs were fried, also my truck was having a problem shitfing once those went but i also had that problem, perhaps yours is somehwta liek that as well... hope i could help

Posted on Aug 08, 2009

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

I have a 1995 GMC 1500 with 5.7 truck that the ABS Light comes on and then the tranny starts jumping gears and speedo goes crazy- Changed ignition switch and that did not help.

Posted on Apr 13, 2010

  • wolfsprt Apr 21, 2011

    It is probaly the sppedo pick up, mine did the exact same thing and an $80 part fixed it. the speedo pick up ties into the abs trans and sppedo.


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • GMC Master
  • 1,810 Answers

Did you plug the sensor back in and didyou reset the computer by disconecting the batery

Posted on Jul 31, 2009

1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

ABS light is on 95 GMC sierra k2500 4x4 light was on before i did a brake job on all 4 wheels how do you turn it off

Doing a brake job has nothing to do with the ABS system .There are three or four wheel speed sensors , depending on the type system . A EBCM - electronic brake control module controls the system .An if the light is on there is DTC - diagnostic trouble code stored in the EBCM ! A diagnostic tool that can read these codes has to be hooked up the vehicle to see what code is stored an then diagnosed . If you are unfamiliar with this your best bet would be to take your vehicle to a qualified repair shop . There is no just turning it off .

Sep 15, 2016 | 1995 GMC Sierra

3 Answers

I have a 2005 GMC Sierra. Afew years ago I started having trouble with the A/C fan. Found overheating at connections on control module. Jumped some wires and have every speed except highest. Was s

If you don't have wiring diagrams,can't read them,&
or work on your own vehicles & their technology,then
a repair shop or different dealer, is you only option,that
question you knew the answer to

Sep 07, 2014 | 2005 GMC Sierra

1 Answer

Transmission control module location on 1995 gmc k1500 z71 4x4

sounds like a bad ground connection.. find and secure all you can and reboot...good luck

May 15, 2013 | 1995 GMC Sierra

1 Answer

ABS warning light stayed on even after I replaced the front brake pads.

No such thing as resetting codes, to fix anything

The codes are used to diagnose the system with the problem

A local repair shop can help you

Jul 02, 2012 | 2005 GMC Envoy Denali

1 Answer

ABS problem with GMC 2002 Sierra

its a low speed abs activation the problem is in the front sensors they need to be cleaned or replaced they [or one] probably has some corrosion on the sensor --[the 99 chevy tahoes had a limited recall over this issue and the fix was to remove and clean the abs sensor or if to corroded replace ] this problem doesnt set off an abs code or trouble light also sometimes the abs will activate by itself at under 4 mph without even touching brake

May 15, 2010 | 2002 GMC Sierra

1 Answer

When braking on hard surface, just before dead stop, the last few feet, the ABS brakes takes over and the veh caries on a few more feet, finishing with a slow stop. The 4 wheels braking system were bled...

There was a TSB on this issue with your Sierra, a faulty or dirty ABS sensor is the cause of this problem. The fix is simple, just clean the ABS sensor at the front hub with brake parts cleaner and inspect the wire leads. At worst you may have to replace the sensor it self. Good luck

Feb 17, 2010 | 2003 GMC Sierra 1500

1 Answer

95 olds cutlass supreme sl with 3.1 6 cyl. ABS and Brake light stays on. Brake pedal is hard to push but front brakes work. Back brakes don't work at all. Took the brake lines off at the rear caliper and...

you may have a ABS problem. I would drive it and attemp to skid the tires an dsee if the pump activates. sometimes this will unstick any valves inside the ABS unit. you may need to have a qualified repair shop check deeper. the ABS will have a code, and a scanner will be needed to check further.

Oct 19, 2009 | 1995 Oldsmobile Cutlass Supreme

3 Answers

Both brake and abs lights are on. I've replaced both front wheel hubs, and checked all fuses.cant seem to locate the problem

you have an ABS code in the ABS computer. You most likely damaged an ABS sensor. even after myouo fix this you will need to get the code cleared
NOTE: autozone wont be able to access the ABS computer.

Aug 03, 2009 | 2001 GMC Sierra 1500HD

2 Answers

2000 GMC Sierra 1500 ABS and Brake lights

Have you by chance checked your fluid? If not, you may want to do that, it could show that you need brakes if it is low. If that doesn't do it, the mechanic may be right about a sensor, but just the wrong one. Hope that helps.

Feb 15, 2009 | 2000 GMC New Sierra 1500

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

2,386 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides